Mendota FV46 Скачать руководство пользователя страница 54

Страница: 54 / 96

85-03-01108

FV46

Page

4.7

TO REMOVE DOOR

Use the glass latch tool to disconnect the spring latches from the glass

frame. Insert tool into hole in latch, pull towards you and rotate 180-

degrees to disengage top latches. Remove tool. There are two spring

latches on top of this gas fireplace. Always make certain the hook glass

latches are in the upside-down position after removing the glass frame.

This upside-down latch position will make it easier to reinstall the glass

frame later.
With both hands, rotate top edge of glass frame away from unit,

approximately 8”.

Lift glass frame up 1”, at an angle, and move away from unit.

Door is now free from unit.

NOTE: Always check glass gasket condition and gasket seal any time the glass door is removed and when

reinstalling glass door.

4.8

TO REPLACE DOOR

Line up the two bottom tabs in glass frame bottom (left and right sides) with slots on the sides of the firebox bottom.

Insert tabs into slots and center tabs in slots, left to right.

Center glass frame over firebox; left to right.

After door has been placed into slots, rotate door towards firebox until gasket seal is touching the firebox frame.

Use the tool provided to connect the spring latches to the glass frame. Insert tool into hole in spring latch, pull latch

towards you, rotate latch so the hook is facing downward then release latch to hook to door frame.

Door is now connected and sealed to unit.

INSERT TAB IN SLOT

Содержание FV46

































































































Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды

Mendota FV46, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды