Mendota FV46 Скачать руководство пользователя страница 53

Страница: 53 / 96

85-03-01108

FV46

Page

4.6

BENDING UP THE SHIPPING CLIPS

Once the unit is detached from the pallet by removing the securing lag screws that hold these shipping clips to the pallet, either

bend these clips up 90-degrees or break them off using a screw driver and back and forth cold working motion (see below). A

bending relief is provided within the clip to ease bending or breaking. Bending the shipping clips up or removing them will be

necessary for Fireplace units which are to be installed in narrow width or shallow depth openings.
To bend the clips up or to break them off, follow these procedures:
1.

Insert the tip of a flat screwdriver (longer screwdriver is better) under the clip.

Lift screwdriver handle upwards and bend the clip up about 45-degrees.

Remove screwdriver. Insert screwdriver tip into one hole in clip. Lift screwdriver up. To break clip off, repeat up down

motion of screwdriver seven to eight times.

Figure 4-4 Shipping Clip

STEP 1 & STEP 2

Figure 4-5 Bend Up Clip 1

STEP 3

Figure 4-6 Bend Up Clip 2

Содержание FV46

































































































Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды

Mendota FV46, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды