Mendota FV46 Скачать руководство пользователя страница 28

Страница: 28 / 96

85-03-01108-C

FV46

Page

Suitable Mantel, Facing & Hearth Pad Materials

Materials used in areas designated as non-combustible must be rated as non-combustible per NFPA 220 Standard on Types of

Building Construction, or reported as passing ASTM E 136, Standard Test Method for Behavior of Materials in a Vertical Tube

Furnace at 750 Degrees C.

WARNING: Common Finishing Materials Not Approved for use.

Paper faced gypsum board (drywall) including Type X Fire Rated board is not a non-combustible material. These boards are

not approved for use in the non-combustible zone of the fireplace.

WonderBoard brand boards are commonly used as a backerboard for tile. WonderBoard backerboard is not a non-

combustible material and is not approved for use in the non-combustible zone of the fireplace. In addition, WonderBoard

off-gasses when heated and should not be used anywhere near the fireplace.

Information for common materials used is given below. It is recommended that finishing material used on the wall over the

fireplace has a depth of at least 1”. This is the depth of the finishing guides on the fireplace and will result in the best final

appearance. Mendota does not guarantee any materials used around the fireplace. Mendota disclaims any and all liability for

any damage to finishing materials including warping, discoloring, cracking, peeling or flaking. This also includes any off-gassing

or unpleasant smells from materials when they are heated.

R-Values of Common Finishing Materials

R-Values of Hearth Pad Boards

Material

Thickness

R-Value

Application

Mineral Fiber Board (Micore 160, 300, SB)

1/2"

1.2 – 1.4

Only approved for use as an insulator

under other non-combustible finishing

material for a hearth pad.

Do not use on the face of a fireplace or

wall.

Cearmic Board (Rescor 360)

1/2"

1.11

Cearmic Board (Fiberfrax Duraboard LD)

1/2"

1.10

R-Values of Common Finishing Materials

Material

Thickness

R-Value

Application

SkamoEnclosure Board

1”

0.410

Best option for a smooth wall finish. Least chance

of cracking from heat.

Promat Promafour

1”

0.410

Cement Board (Hardibacker 500)

1/2"

0.200

Best used as a backer board for tile or natural

stone installations.

Not recommended as a smooth wall finish unless

used with a Cool Wall heat transfer system.

Cement Board (Hardibacker)

1/4"

0.130

Common Brick

2-1/4"

0.450

Common non-combustible materials used around

a fireplace. Can be used on the wall or hearth

pad. Install these materials per the

recommendations in the following sections.

Common Brick

0.800

Thinset Mortar

1/4"

0.100

Concrete (150 lbs/Cubic Foot)

0.07

Ceramic Tile

1/4"

0.25

Flagstone

0.079

Granite

0.05

Limestone

0.08

Marble

0.08

Sandstone

0.079

Slate

0.100

Содержание FV46

































































































Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды

Mendota FV46, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды