Mendota FV46 Скачать руководство пользователя страница 76

Страница: 76 / 96

85-03-01108

FV46

Page

5.5

REMOTE CONTROL OPERATING INSTRUCTIONS

To Turn on the Fireplace

NOTE: If the fireplace does not respond to the remote-control commands but it responds by beeping only, the fireplace system

may have entered “safety lockout” mode. To reset the system, see

Chapter 5.11.12 Why won’t my fireplace turn on?.

Press the on/off button. The remote-control display will show all active icons on the screen.

Select the thermostat mode by pressing the thermostat button: OFF (meaning Manual), ON (meaning Normal Thermostat)

or Smart (meaning Smart Thermostat).

If the thermostat icon displays as “OFF” (Manual), the fireplace will ignite and start on Hi.

If the thermostat icon displays as “ON” (Normal Thermostat), the fireplace will only ignite if the thermostat

temperature is greater than the room temperature.

If the thermostat icon displays as “SMART” (Smart Thermostat), the fireplace will only ignite if the

thermostat temperature is greater than the room temperature.

To Turn off the Fireplace

Press the on/off button.

Understanding Your Remote-Control Icons

Your remote control displays and controls the following functions. See below for detailed control explanations.
Note: the “AUX On” function is not used in this fireplace.

Figure 5-4 Remote Control Icons

Содержание FV46

































































































Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды

Mendota FV46, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды