Mendota FV46 Скачать руководство пользователя страница 61

Страница: 61 / 96

85-03-01108

FV46

Page

4.11

VENTING

WARNING: Proper installation of the vent system, as required in this manual, is vital to the performance of

this Fireplace. Oversights or failure to conform to all installation requirements will void the applicable

warranty.

The FV46 Fireplace must be vented to the outside and must use a rigid coaxial ducting system.

This heater must be properly connected to a venting system in accordance with the manufacturer's

installation instructions. Operation of this heater when not connected to a properly installed and maintained

venting system can result in carbon monoxide (CO) poisoning and possibly death.

If the vent system of this appliance is disconnected for any reason, the vent and air intake systems must be

properly reassembled and resealed before this appliance is put into use.

CAUTION:

Each installation must conform to all local, state and national codes. Refer to the national fuel

gas code and local zoning and code authorities for details on installation requirements. The Mendota

Fireplaces must be vented to the outside in accordance with the latest edition of the National Fuel Gas Code.

In the absence of local codes, the installation must conform with National Fuel Gas Code ANSI Z223.1 (NFPA

54), or Canadian Code CAN1-B149 or most current edition, also known as NFPA 54. Do not connect this

Fireplace to a chimney flue serving a separate solid fuel or gas-burning appliance.

Do Not Use any silicone sealants at pipe joints. Stove gasket cements may be used at pipe joints but is not

required.

Required Clearances to Vent Pipes

•

Clearance to top of a horizontal vent pipe or the top of a horizontal discharge elbow shall be 3” minimum.

•

Clearance to the sides of a horizontal vent pipe and elbows shall be 1” minimum.

•

Clearance to the bottom of a horizontal vent pipe and elbows shall be 1” minimum.

Wall Thimble Information

A wall thimble is required to be installed when penetrating any combustible wall, regardless of whether the wall Is an internal

wall or an external wall.
Wall thimbles are designed to reduce the required clearances to the exterior surfaces of the vent pipe that pass through

combustible walls. The hole size that is specified to be cut in the wall for installation of the wall thimble takes into consideration

the reduced clearance requirement.

Содержание FV46

































































































Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды

Mendota FV46, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды