Mendota FV46 Скачать руководство пользователя страница 1

Страница: 1 / 96

85-03-01108-J

FV46

Installation and Operating Instructions

MODEL NO. AA-11-03763 FV46 FULLVIEW DIRECT VENT GAS FIREPLACE HEATER

WARNING:

If the information in these instructions is not

followed exactly, a fire or explosion may result causing

property damage, personal injury or loss of life.

AVERTISSEMENT

. Assurez-vous de bien suivre les instructions

données dans cette notice pour réduire au minimum le risque

d'incendie ou d'explosion ou pour éviter tout dommage

matériel, toute blessure ou la mort.

- Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.
- WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not

use any phone in your building.

•

Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

•

If you cannot reach your gas supplier, call

the fire department.

- Installation and service must be performed by a

qualified installer, service agency or the gas

supplier.

Ne pas entreposer ni utiliser d'essence ni d'autres vapeurs

ou liquids inflammables dans le voisinage de cet appareil

ou de tout autre appareil.
- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d'allumer d'appareil.

• Ne touchez à aucun interrupteur. Ne pas vous servir des

téléphones se trouvant dans le bâtiment où vous trouvez.

• Appelez immédiatement votre

fournisseur de gaz depuis

un voisin. Suivez les instructions du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incendies.
- L'installation et l'entretien doivent être assurés par un

installateur ou un service d'entretien qualifié ou par le

fournisseur de gaz.

This appliance may be installed in an aftermarket,

permanently located, manufactured home (USA

only) or mobile home, where not prohibited by local

codes.
This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gasses, unless a

certified kit is used.

Cet appareil peut être installé dans une maison

préfabriquée (É.-

U. seulement) ou mobile déjà installée à

demeure si les règlements locaux le permettent.
Cet appareil doit être utilisé uniquement avec les types de

gaz indiqués sur la plaque signalétique. Une trousse de

conversion est fournie avec cet appareil.

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and must be installed.

Une barrière conçue pour réduire le risque de brûlures

du verre chaud est fournie avec cet appareil et doit être

installée.

Содержание FV46

































































































Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды

Mendota FV46, Инструкция по установке и эксплуатации

Результаты поиска

Содержание FV46

Отзывы:

Бренды по названию

Популярные бренды