manualshive.com logo in svg

MaxVision 8230 XRA2 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
MaxVision 8230 XRA2 series Скачать руководство пользователя страница 82

76 

MaxPac Dual/Triple-Screen 8230 XRA2/3-Series User Operation and Maintenance Guide 

 

 

Appendix A: Creating and Using 
Backup Images (Including 
Restoring Your OS) 

Introduction 

Every MaxVision system comes equipped with a 

MaxVision Recovery DVD

. In addition to an image of 

your operating system, this disc also contains a copy of the 

Acronis True Image™

 application from 

Acronis (www.acronis.com). 

Acronis True Image

 is a superb tool for operating system (OS) 

deployment, software distribution, back-up, and disaster recovery. In particular, this utility allows you 
to make reliable backups of your system drives, including applications and critical data. There are two 
primary scenarios that need be considered as follows: 

Restoring the MaxVision-supplied Image 

This is the worst-case scenario. It assumes that your system has undergone some catastrophic 
failure such that – under the direction of MaxVision support – you are going to replace your primary 
hard drive(s) and/or restore the original MaxVision-supplied image. In this case, you will lose any 
applications and data that you have installed, loaded, or created on your main “C:” drive/partition. 

Note: 

If you do re-load the original MaxVision-supplied image, you will also have to re-run the 

initialization procedures – including re-activating/re-registering your OS license – as described earlier 
in this manual. 

Creating Your Own Image 

This scenario assumes that you have added new applications, loaded or created new datasets, and 
generally configured and customized your MaxVision system the way you like it. At this stage, 
before you deploy the system, it is strongly recommended that you use the 

Acronis True Image

 

application to create an image of the system. Similarly, as you add additional applications or 
generate additional datasets, it is strongly recommended that you create periodic backup images. 
This greatly facilitates your ability to return the system to a “known good state” should any problems 
arise (such as a virus attack or a hard drive failure) at some stage in the future. 
 
For the purposes of this example, we will assume that you are writing your image to CD media (as 
opposed to DVD), and that the image will occupy two CDs. 
 
1)  Power-down the system. 

2)  Ensure that the bootable recovery DVD supplied in the accessory pack is in the system's 

CD/DVD drive. In the case of a multiple DVD image, ensure Disk #1 is in the drive. 

3)  Power-up the system. This will automatically launch the Acronis application as shown in Figure A-1. 

 

Содержание 8230 XRA2 series




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды