manualshive.com logo in svg

MaxVision 8230 XRA2 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
MaxVision 8230 XRA2 series Скачать руководство пользователя страница 74

68 

MaxPac Dual/Triple-Screen 8230 XRA2/3-Series User Operation and Maintenance Guide 

 

 

7)  The power and video cables for the right monitor (and also and the soft power cable) must be 

removed from the inner chassis cover cable channel as shown in Figures 3-95 and 3-96. 

 

Figure 3-96 

 

Figure 3-97 

8)  The center and left monitor power and video cables must be removed from the inner chassis 

cover cable channel as show in Figure 3-97 

9)  You will need a second person to hold the monitor assembly while you lift the inner chassis out of 

the outer chassis Figure 3-98. 

 

Note

: As the weight of the inner chassis is removed, the display assembly and outer chassis will 

topple over if not being held securely. 

 

Figure 3-98 

 

Figure 3-99 

10) Next, the display assembly should be rotated down as illustrated in Figure 3-99. 

11) Now, tilt the alluminum inner chassis lid into a vertical orientation so as to facititate access to the 

motherboard. There are two screws on either side of the cooling fan assembly. Use a Phillips #2 
screwdriver to loosen these captured screws (Figures 3-100 and 3-101). 

Содержание 8230 XRA2 series




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды