manualshive.com logo in svg

MaxVision 8230 XRA2 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
MaxVision 8230 XRA2 series Скачать руководство пользователя страница 11

 

MaxPac Dual/Triple-Screen 8230 XRA2/3-Series User Operation and Maintenance Guide 

 

5

Power Requirements 

MaxPac 8230 XRA2/3-Series power supplies are auto-sensing 100 to 240 VAC, 50 to 60Hz units. 
Ensure that the supplied power is sufficient, stable, and without spikes or surges for operation of your 
MaxPac and other required equipment. 

Attaching the Filters 

1)  Stand the MaxPac system upright on the table; also, remove the two "Baghdad Filters" from the 

accessory box (Figure 1-6). 

 

Figure 1-6 

 

Figure 1-7 

2)  The rear portion of the filter assembly is already attached to the main chassis. Present the front 

portion of the left-hand filter assembly (including its filter element) to the rear portion of the 
assembly on the main chassis. Use the flanges to engage the left-hand side of the assembly as 
shown in Figure 1-7, and then engage the Velcro on the right-hand side of the assembly to its 
counterpart on the main chassis. 

3)  Similarly, present the right-hand filter assembly and filter element to the rear portion of the 

assembly, which is already attached to the main chassis. Use the flanges to engage the right-
hand side of the assembly as shown in Figures 1-8 and 1-9, and then engage the Velcro on the 
left-hand side of the assembly to its counterpart on the main chassis. 

 

Figure 1-8 

 

Figure 1-9 

Содержание 8230 XRA2 series




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды