manualshive.com logo in svg

MaxVision 8230 XRA2 series, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
MaxVision 8230 XRA2 series Скачать руководство пользователя страница 37

 

MaxPac Dual/Triple-Screen 8230 XRA2/3-Series User Operation and Maintenance Guide 

 

31

12) Observe that the replacement drive has now been incorporated into the RAID 5 array as 

illustrated in Figure 2-43 (note that this array is still shown as being DEGRADED). 

 

Figure 2-43. 

When the new disk has been fully integrated into the array, the interface will reflect the 
completion of the rebuild. 
 

Note:

 This rebuild process can take a significant amount of time (14 hours in the case of our 

example using 400 GB disks). 
 

Note:

 The rebuild process is performed in the background, so you can continue to use your 

system while the rebuild is taking place. 

 

Configuring the RAID Array  

(with Hot Spare and System Partition on RAID Array) 

Note that these discussions reflect system configurations that have the system partition established 
on the RAID array itself (leaving a hot-spare drive) as illustrated in Figure 2-44. Configurations with a 
separate system drive are discussed earlier in this chapter. 
 
When you take possession of your MaxPac 8230 XRA2/3, the RAID system will already have been 
established, initialized, and verified. The instructions in this section are intended to address those rare 
situations where you need to replace a degraded/failed drive or you wish to rebuild the RAID system 
from the ground up. 
  
Your MaxPac system can contain up to four SATA hot-swappable hard disk drives presented in a  
4-drive disk caddy. This caddy is located on the lower left-hand side of the main chassis under the 
"Baghdad Filter" assembly as shown to the left of Figure 2-44 (the numbering of the disks is as shown 
to the right of Figure 2-44). The main array – including the system partition – occupies disks 00, 01, 

Содержание 8230 XRA2 series




































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды