
2-3
CD25
SAFETY INFORMATION
2
Published 1-06-2017 Control # 579-01
manual and
Load Chart
must be readily available to the
operator at all times and must remain in the cab (if equipped)
or operator’s station while the crane is in use.
The
Operator Manual
supplied with and considered part of
your crane must be read and completely understood by each
person responsible for assembly, disassembly, operation
and maintenance of the crane.
No personnel shall be allowed to climb onto the crane or
enter the crane cab or operator’s station unless performance
of their duties require them to do so, and then only with
knowledge of the operator or other qualified person.
Allow
No One
other than the operator to be on the crane
while the crane is operating or moving, unless they are
seated in a two-man cab.
Do not remove
the
Load Chart
, this
Operator Manual
, or
any decal from this crane.
Inspect the crane every day (before the start of each shift).
Ensure that routine maintenance and lubrication are being
dutifully performed. Don’t operate a damaged or poorly
maintained crane. You risk lives when operating faulty
machinery - including your own.
If adjustments or repairs are necessary, the operator shall
notify the next operator.
OPERATOR QUALIFICATIONS
Qualified person
is defined as one who by reason of
knowledge, training and experience is thoroughly familiar
with crane operations and the hazards involved. Such a
person shall meet the operator qualifications specified in
Occupational Safety and Health Administration (OSHA)
Regulations (United States Federal Law), in ASME B30.5
American National Standard, or in any other applicable
federal, state or local laws.
Ensure that all personnel working around the crane are
thoroughly familiar with safe operating practices. You must
be thoroughly familiar with the location and content of all
placards and decals on the crane. Decals provide important
instructions and warnings and must be read prior to any
operational or maintenance function.
Refer to the
Parts Manual
for this crane for the locations of all
safety decals.
You must be familiar with the regulations and standards
governing cranes and their operation. Work practice
requirements may vary slightly between government
regulations, industry standards, and employer policies so a
thorough knowledge of all such relevant work rules is
necessary.
An untrained operator subjects himself and others to death
or serious injury.
You must not operate this crane unless
:
•
You have been trained in the safe operation of this
crane.
•
You read, understand, and follow the safety and
o p e r a t i n g r e c o m m e n d a t i o n s c o n ta i n e d i n t h e
manufacturer’s manuals, your employer’s work rules,
and applicable government regulations.
•
You are sure the crane has been inspected and
maintained in accordance with the manufacturer’s
manuals and is operating properly.
•
You are sure that all safety signs, guards, and other
safety features are in place and in proper condition.
Do not attempt to operate the crane unless you are trained
and thoroughly familiar with all operational functions.
Controls and design may vary from crane to crane; therefore,
it is important that you have specific training on the particular
crane you will be operating.
Training is ESSENTIAL for proper crane operation. Never
jeopardize your own well-being or that of others by
Reference Only
Содержание CD25
