Magnum Dimensions MMSA Series Скачать руководство пользователя страница 8

Страница: 8 / 58

Introduction

1.2.1 Inverter Applications for Mobile Installations

In mobile applications, an inverter/charger provides power to the

AC loads using the energy stored in the batteries and recharges the

batteries when shorepower or an onboard generator is available.

1.3 Advantages of a Pure Sine Wave Inverter

Today’s inverters come in two basic output waveforms: modi

sine (which is actually a modi

ed square wave) and pure sine wave.

Modi

ed sine wave inverters approximate a pure sine waveform and

will run most appliances and electronics without any problems.
The output of a pure sine wave inverter is equal to, or in many

ways, better than the shorepower used in your home. Virtually any

electronic device will operate from a pure sine wave inverter. Motors

run cooler, microwaves usually cook faster, and clocks keep better

time just to name a few examples.

1.4 Appliances and Run Time

The MMSA1012 inverter/charger can power a wide range of

household appliances. As with any appliance using batteries for

power, there is a certain length of time that it can run—this is called

“run time”. Actual run time depends on several variables including

the size and the type of appliance, the type of batteries installed in

your application, as well as the battery’s capacity and age. Other

factors such as the battery’s state of charge and temperature can

also affect the length of time your appliances can run.
Depending on your inverter capacity, larger electrical appliances

can be used for short durations. However, loads that are used for

longer periods such as stoves or water heaters can quickly drain

your batteries and are not recommended for inverter applications.
All electrical appliances are rated by the amount of power they

consume. The rating is printed on the product’s nameplate label,

usually located on its chassis near the AC power cord. Even though it is

dif

cult to calculate exactly how long an inverter will run a particular

appliance, the best advice is trial and error. Your MMSA1012 inverter

has a built-in safeguard that automatically protects your batteries

from being over-discharged.

1.5 Standard Features and Benefi ts

The MMSA1012 inverter/charger

converts 12-volt direct current

(VDC) power from your battery to 120-volt alternating current

(VAC) power.

With the multi-stage battery charger feature, the

incoming AC power is optimized using Power Factor Correction

(PFC) technology to keep the inverter’s battery bank fully charged.

The MMSA1012 is designed to allow easy installation and use, and

its die-cast aluminum baseplate ensures maximum durability and a

cooler, more ef

cient operation.

Содержание MMSA Series



























































Результаты поиска

Содержание MMSA Series

Отзывы:

Magnum Dimensions MMSA Series, Руководство пользователя, Страница: 8 / 58

Результаты поиска

Содержание MMSA Series

Отзывы: