Magnum Dimensions MMSA Series Скачать руководство пользователя страница 38

Страница: 38 / 58

Operation

BULK

(blue)

ABSORB

(yellow)

FLOAT

(green)

Description

OFF

Absorb Charge Stage

– Charger is

in Constant Voltage stage and begins

after the bulk voltage is reached. The

DC charging current will taper down

in order to maintain the battery at the

absorb target voltage

OFF

Blink

(x1/sec)

OFF

Charger Back-off

(in Absorb Charge

mode) – Charger is in Charger Back-

off

, limiting charging current to the

battery.

OFF

Float Charge Stage

(in Float Charge

mode) – Float Charge occurs at end

of absorb charging time—reduces the

charge voltage to maintain the batteries

at the

oat target voltage

OFF

Blink

(x1/sec)

Charger Back-off

– Charger is in Float

Charge mode and in Charger Back-off

limiting charging current to the battery.

OFF

Blink

(x2/sec)

Full Charge Stage

– Full Charge stage

turns the charger off and monitors battery

voltage to determine when to continue

charging. After four hours in Float Charge

mode, charger goes to Full Charge mode.

If battery voltage drops to a low level

(12.7 VDC), the charger automatically

initiates another

oat charge.

1st

2nd

3rd

Equalize Charge Stage

– Charger

is in the Equalize Charge stage,

regulating the current to maintain the

battery at the equalize target voltage

Note: Each charge status LED indicator

comes on quickly in sequence.

Note

Target Voltage – The temperature compensated voltage regulation

set-point. The battery will be regulated to the voltage setting determined

by the active charge stage (i.e., Absorb, Float, or Equalize) and the Battery

Type DIP switch setting; and includes any voltage increase or decrease

based on the temperature around the BTS.
Note

Charger Back-off occurs if: 1. The FET or internal temperature is

very hot (the charger reduces the charge rate to maintain temperature); or,

2. The AC input voltage has fallen below 85 VAC (the charger reduces the

charge rate to help stabilize the incoming AC voltage).
Note

There is a two-second pause between each blink sequence.

Example: Blink (x2 sec) means the LED blinks twice within a second and

then is off for 2 seconds—this sequence continues while in this status.

Содержание MMSA Series



























































Результаты поиска

Содержание MMSA Series

Отзывы:

Magnum Dimensions MMSA Series, Руководство пользователя, Страница: 38 / 58

Результаты поиска

Содержание MMSA Series

Отзывы: