Magnum Dimensions MMSA Series Скачать руководство пользователя страница 11

Страница: 11 / 58

Introduction

Figure 1-4, Right Side Features

Battery Temperature Sensor Connection

–

a RJ11 port

that accepts the supplied remote Battery Temp Sensor

(BTS) cable.

Remote Connections

– two RJ11 ports that allow two

remote controls to be connected for adjusting/monitoring

inverter and charger operation.

Dual In-line Package (DIP) Switch

– 10 individual slide

switches that are used to determine the MMSA inverter/

charger’s operating parameters.

3-Port Terminal Block

– three spring-loaded clip

terminals to connect an optional 20-amp DC auxillary

device, a ignition control switch, and a ground remote

control switch.

Exhaust Vent

–

ventilation openings that allow heated air

to be removed by the internal cooling fan

Model/Serial Number Label

– includes model/serial

number and provides speci

cations and information on the

inverter and charger.

Figure 1-5, Back Side Features

Содержание MMSA Series



























































Результаты поиска

Содержание MMSA Series

Отзывы:

Magnum Dimensions MMSA Series, Руководство пользователя, Страница: 11 / 58

Результаты поиска

Содержание MMSA Series

Отзывы: