Magnum Dimensions MMSA Series Скачать руководство пользователя страница 14

Страница: 14 / 58

Installation

2.0 Installation

2.1 Pre-Installation

Before installing the inverter, read

the entire Installation section.

The more thorough you plan in the beginning, the better your

inverter needs will be met.

WARNING:

Installations should be performed by quali

personnel, such as a licensed or certi

ed electrician. It

is the installer’s responsibility to determine which safety

codes apply and to ensure that all applicable installation

requirements are followed. Applicable installation codes

vary depending on the speci

c location and application of

the installation.

Info:

Review the safety information on pages ii-iii before

proceeding with your installation.

The basic system diagram shown in Figure 2-1

should be reviewed

to assist you in planning and designing your installation.

2.1.1 Unpacking and Inspection

Carefully remove the MMSA1012 inverter from its shipping container

and inspect all contents. Verify the following items are included:
• MMSA1012

inverter/charger

• Connected positive and negative battery cables with Anderson

connector attached

• Battery Temperature Sensor
• MMSA1012 Owner’s Manual
• Warning

label

If items appear to be missing or damaged, contact your authorized

dealer or Sensata.
If at all possible, keep your shipping box. It will help protect your

inverter from damage if it ever needs to be returned for service.
Save your proof-of-purchase as a record of your ownership; it will

also be needed if the unit should require in-warranty service.
Record the unit’s model and serial number in the front of this manual

in case you need to provide this information in the future. It is much

easier to record this information now, instead of trying to gather it

after the unit has been installed.

Содержание MMSA Series



























































Результаты поиска

Содержание MMSA Series

Отзывы:

Magnum Dimensions MMSA Series, Руководство пользователя, Страница: 14 / 58

Результаты поиска

Содержание MMSA Series

Отзывы: