Magnetek Impulse G+ series 4, Инструкция по эксплуатации

Страница: 262 / 276

IMPULSE®•G+ & VG+ Series 4 Instruction Manual – February 2017
A-8
C09-09 DIO Terminal 8 0F 0–FF -- 5-43
C09-10 DIO Terminal 9 0F 0–FF -- 5-43
C09-11 DIO Terminal 10 0F 0–FF -- 5-43
C09-12 DIO Terminal 11 0F 0–FF -- 5-43
C09-13 DIO Terminal 12 0F 0–FF -- 5-43
C09-14 DIO Terminal 13 0F 0–FF -- 5-43
C09-15 DIO Terminal 14 0F 0–FF -- 5-43
C09-16 DIO Terminal 15 0F 0–FF -- 5-43
C09-17 DIO Terminal 16 0F 0–FF -- 5-43
C10-01 Load Weight 0 0–2 -- 5-44
C10-02 LW Start 0 0, 1 -- 5-44
C10-03 LW Display Hold 0 0, 1 -- 5-44
C10-04 LW Conversion 0 0–39999 -- 5-44
C10-05 Test Freq 6 0–E01-04 Hz 5-44
C10-06 Unit Displayed 4 0–4 -- 5-44
C10-07 Holding Time 1.00 0.00–2.55 sec 5-44
C10-09 Full Load Torque 100.0 0.0–200.0 % 5-44
C10-10 No Load Torque 20.0 0.0–200.0 % 5-44
C11-01 Slack Cable 0 0–2 -- 5-46
C11-02 Action at SLC 2 0–2 -- 5-46
C11-03 SLC Detect Torq 30 -50–100 % 5-47
C11-04 SLC Detect Spd 1 2 0–E01-04 Hz 5-47
C11-05 SLC Delay Time 1 0.50 0.00–2.55 sec 5-47
C11-06 SLC Detect Spd 2 60 0–E01-04 Hz 5-47
C11-07 SLC Delay Time 2 0.10 0.00–2.55 sec 5-47
C11-08 Snap Shaft 0 0, 1 -- 5-48
C11-09 Action at Snap 0 0, 1 -- 5-48
C11-10 Delta Speed 1.0 0.0–E01-04 Hz 5-48
C11-11 Delay Time 250 0–2000 ms 5-48
C11-12 Gear Ratio Num 10000 1–65535 -- 5-48
C11-13 Gear Ratio Den 10000 1–65535 -- 5-48
C12-01 Brake Jog Delay 0.0 0.0–100.0 sec 5-49
C12-02 Brake Run Delay 0.0 0.0–100.0 sec 5-49
C12-03 Delay-ON Timer 0.0 0.0–3000.0 sec 5-49
C12-04 Delay-OFF Timer 0.0 0.0–3000.0 sec 5-49
C12-05 Maintenance Tmr 0 0–32767 hr 5-50
C12-06 Maintenance Gain 0.50 0.00–1.00 -- 5-50
C12-07 LdShare Flt Time 1.50 0.00–2.55 sec 5-50
C13-01 Inch Run Time 1.00 0.00–2.55 sec 5-51
C13-02 Repeat Delay Tim 1.00 0.00–2.55 sec 5-51
C13-03 Index Run Ref 0.10 0.01–60.00 Hz 5-53
Parameter Parameter Name Default Range Units Reference
* Initial value set by X-Press Programming (Table 4-6, 4-7, or 4-8 on pages 4-12, 4-13, and 4-14).
** Initial value dependent on drive size, which is determined by O02-04 (kVA Selection).
*** Value is automatically set during auto tuning.
**** 0.0–25.5 seconds is extended to 0.0–6000.0 seconds when B05-16 = 1.