![background image](http://html1.mh-extra.com/html/magnetek/impulse-g-series-4/impulse-g-series-4_instruction-manual_3660463125.webp)
IMPULSE®•G+ & VG+ Series 4 Instruction Manual – February 2017
5-39
Table 5-32: No Load Brake Parameter Settings
Parameter Display
Function
Range
Default
Model
C08-01
Torque Comp Time Amount of time for the Torque
Comp value to reach 300%.
0.00–2.55 sec
1.00
VG+
C08-02
IFB OK Time
Sets the amount of time to look for
the current feedback to be OK
before posting a BE2 alarm.
Setting this parameter to 0.00 will
disable torque proving at start &
eliminate BE2 detection (consult
factory before disabling torque
proving).
0.00–2.55 sec
1.00
VG+
C08-03
Min Brk Rel Trq
Minimum brake release torque.
0–300%
10
VG+
C08-04
Rollback Timer
Sets the amount of time for the
brake to release and for brake
feedback to be received into the
Brake Answer Back Multi-Function
Digital Input at start before posting
BE1 or BE4 alarm. It is also the
time period during which the
amount of rollback is checked.
0.00–2.55 sec
0.30
G+/VG+
C08-05
Rollback Count
Detection counts for excessive
rollback.
4 pulses = 1 ppr of F01-01
0–15000 pulses 800
VG+
C08-06
BE3/Alt Torq Tim
Time period which C08-07 is
measured. Also see C08-08.
0.00–2.55 sec
0.30
VG+
C08-07
BE3 Detect Count
Detection count for Encoder/
Seized-Brake Alarm (BE3). It is
the minimum encoder pulse count,
during the time period of C08-06,
below which the BE3 alarm is
triggered.
4 pulses = 1 ppr of F01-01
0–15000 pulses 10
VG+
C08-08
Alt Rev Trq Lim
For a LOWER command in the
NLB Hoist Motion Mode only-
Torque limit for time of C08-06 to
prevent driving through a brake
that has failed closed with a load
on the hook.
0–300%
25
VG+
C08-09
Zero Speed Level
Determines speed feedback at
which Load Float activates.
0.0–10.0 Hz
1.0
VG+
C08-10
Load Float Time
After stop command time period
during which the load is held at the
zero-position and the electric
brake is not set.
0-65535 sec
10*
VG+
C08-11
Brake Set Delay
Sets the amount of time for the
brake to set and for brake
feedback to be removed from the
Brake Answer Back Multi-Function
input at stop before posting a BE5
Alarm.
0.0–25.5 sec
0.7
G+/VG+
C08-12
BE6 Detect Time
Time period during which the
electric brake is set and tested for
sustaining the load.
NOTE: To disable BE6 detection,
set C08-12 to 0.0.
0.0–25.5 sec
5.0
VG+
C08-13
BE6 Max Count
Total pulse counts must be less
than C08-13, during C08-12,
otherwise BE6 alarm.
4 pulses = 1 ppr of F01-01
0–15000 pulses 250
VG+
* Initial value is determined by X-Press Programming (Table 4-6, 4-7, or 4-8 on pages 4-12, 4-13, and 4-14).
**
Содержание Impulse G+ series 4
