IMPULSE®•G+ & VG+ Series 4 Instruction Manual – February 2017
5-50
Maintenance Timer
The “Maintenance Timer” is a maintenance feature that will alert an operator, for example, when the
bearings need to be greased. It consists of a Multi-Function Output (H02-0x–08 = 37) that becomes
active when the total running time has exceeded the amount of time (in hours) programmed in
parameter C12-05 and the frequency reference will be multiplied by a programmable gain (C12-06)
to slow the motion down until the bearings have been greased. An alarm will also be posted on the
Keypad stating “Maintenance Required”. Once the bearings have been greased, the output and
alarm message can be reset by two different methods. One method is through a Multi-Function Input
programmed for Maintenance Reset (H01-01–08 = 5A) and the second method is by pressing the
Mode/Service (Local/Remote) button three consecutive times with no more than 2 seconds between
presses. Press enter to reset the timer. A message will then appear on the keypad stating that the
timer has been reset. The Multi-Function Output will turn off at this time. When C12-01 = 0, the
function is disabled.
Table 5-40: Maintenance Timer Parameter Settings
Load Share
Please refer to page 5-20 for more information on Load Share.
Table 5-41:Load Share Parameter Settings
Parameter
Display
Function
Range
Default
C12-05
Maintenance Tmr
Maintenance Timer Trip Level
0–32767 Hr
0
C12-06
Maintenance Gain
Speed Reference Gain
0.00–1.00
0.50
Parameter
Display
Function
Range
Default
C12-07
LdShare Flt Time
The amount of time to wait for
Slave drives to give a Slave Ready
Signal, when in Load Share,
before triggering a fault.
0.0–25.5 sec
1.5
Содержание Impulse G+ series 4
