![background image](http://html1.mh-extra.com/html/magnetek/impulse-g-series-4/impulse-g-series-4_instruction-manual_3660463162.webp)
IMPULSE®•G+ & VG+ Series 4 Instruction Manual – February 2017
5-76
F01-12
PG2 Rotation Sel
Changing this parameter has the
same effect as swapping A+ and
A- encoder wires.
0, 1
0
VG+
0
Fwd = C.C.W.
1
Fwd = C.W.
F01-13
PG2 #Gear Teeth1
Sets the gear ratio between the
motor shaft and the encoder
(PG).
A gear ratio of 1 will be used if
F01-13 or F01-14 are set to 0.
0–1000
0
VG+
F01-14
PG2 #Gear Teeth2
Sets the gear ratio between the
motor shaft and the encoder
(PG).
A gear ratio of 1 will be used if
F01-13 or F01-14 are set to 0.
0–1000
0
VG+
F01-15
PG2 Output Ratio
Sets the division ratio for the
pulse monitor used of the PG
option card installed to port CN5-
B.
1–132
1
VG+
F01-16
PGO-2-H
Delay time for PGO-2-H
detection. A setting of zero
disables PGO-2-H detection.
Channel 2 is associated with slot
CN5-B.
0–100 ms
15
VG+
F01-21
PG Fdbk Loss Sel
Stopping method when PGO-1-S
or PGO-2-S faults are detected.
Traverse: 0–3
NLB: 1
1
VG+
0
Decel to Stop
Decelerate to stop using the
deceleration time in B05-02.
1
Coast to Stop
2
Fast Stop
Decelerate to stop using the
deceleration time in B05-08.
3
Alarm Only
F01-22
PGO-1-S Det Time
PGO-1-S (CH1) disconnection
detection time. A setting of zero
disables PGO-1-S detection.
0.0–10.0 sec
2.0
VG+
F01-23
PG Overspeed Sel
Sets the stopping method when
an overspeed (OS) fault occurs.
Traverse: 0–3
NLB: 1
1
VG+
0
Decel to Stop
Decelerate to stop using the
deceleration time in B05-02.
1
Coast to Stop
2
Fast Stop
Decelerate to stop using the
deceleration time in B05-08.
3
Alarm Only
F01-24
PG Overspd Level
Sets the overspeed detection
level as a percentage of the
maximum output frequency.
0–120%
105
VG+
F01-25
PG Overspd Time
Sets the time in seconds for an
overspeed situation to trigger a
fault (oS).
0.0–2.0 sec
0.0
VG+
Parameter
Display
Function
Range
Default Model
Содержание Impulse G+ series 4
