![background image](http://html1.mh-extra.com/html/magnetek/impulse-g-series-4/impulse-g-series-4_instruction-manual_3660463214.webp)
IMPULSE®•G+ & VG+ Series 4 Instruction Manual – February 2017
5-128
Copy Function
Table 5-110: Copy Function Parameter Settings
The digital operator has parameter COPY capabilities via built-in non-volatile memory. The digital
operator can READ all of the parameters in the Drive and store them for later, and then WRITE back
to the Drive or into a Drive with the same product code and software number. In order to read the
parameter values and store them into the digital operator, select O04-02 = 1 (Enabled). If you
attempt to READ the data, which overwrites any previously stored data, without first setting
O04-02 = “1: Enabled,” you will get the following error:
After setting O04-02 = 1 (Enabled), it is possible to store parameter values in the digital operator by
setting O04-01 = 1 (INV
OP READ). A successful READ of the parameter values will display:
Parameter
Display
Function
Range
Default
O04-01
Copy Function Sel
Copy parameters to/from keypad
0–3
0
0
COPY SELECT
1
INV
OP READ
Drive
Keypad
2
OP
INV WRITE Keypad
Drive
3
OP
↔
INV VERIFY Keypad
↔
Drive
O04-02
Read Allowable
Enables/disables copy function
0, 1
1
0
Disabled
1
Enabled
O04-07
ChrgCircMaintSet
Sets the value of the Maintenance
Monitor for the soft charge bypass
relay. See U04-06 to check when
the bypass relay may need to be
replaced.
0–150%
0
RDER
READ DATA ERROR
END
READ COMPLETE
Содержание Impulse G+ series 4
