IMPULSE®•G+ & VG+ Series 4 Instruction Manual – February 2017
5-88
43 Timer Function
Function settings by C12-03, C12-04. It is set with timer function output
H02-01–H02-03 = 12.
47 Ref Sample Hold
Analog frequency reference Sample / Hold.
48 Flt Latch Reset
When a function is latched, toggle this input ON and then OFF to clear
the fault.
4B Anti-Shock OFF
When this input is ON, Anti-Shock will be blocked from functioning.
4C DCInj Activate
ON: DC injection braking command, once SFS reaches Zero Speed
53 Comm Test Mode
Communication test mode - Loopback test of Modbus RS-422/485
interface.
55 Drive Enable
When Programmed, must be ON in order for Inverter Ready - Generates
“Can’t Run - Drive Not Ready” Alarm.
“RDY” is displayed in upper right hand corner of LCD when drive is ready.
56 Klixon N.O.
When Closed, Reset run command, use stopping method C03-12,
display KLX - Klixon Alarm on Keypad
57 Klixon N.C.
When Open, Reset run command, use stopping method C03-12, display
KLX - Klixon Alarm on Keypad
58 Brake Answerback
Drive will post BE0, BE4, BE5, BE7 alarm conditions only when
programmed to MFDI. (C08-04, C08-11)
59 Alt F-Ref Up Lmt
Use Alternate Upper Limit Frequency Reference B02-04
5A MaintenanceReset
Resets Maintenance Timer (C12-05–06, U01-52)
5B BE6/8 Up Spd Lmt
Limits Fref to setting in C08-18 (BE6 Up Speed Lmt)
5C Weight Measure
Weight Measurement by C10-01.
5D Load Float Ext
Extends C08-10 Time by adding C08-15 time.
5E M-Spd Gn1 & LF-E
Micro-Speed Gain 1 and Load Float Extension Time. (Combination of
MFDI “E” and “5D” ON)
5F Phantom Flt N.C.
Phantom Fault N.C. - Stops motion based C03-09 but does not change
Keypad display. RUN L.E.D. on keypad blinks.
60 Index Enable
Enables indexing function (Hidden when B03-03 = 1 Coast to Stop)
61 Brake Test
Motor pushes against brake up to programmable torque setting C08-24
at programmable frequency C08-25. Disables PG Faults during this
condition.
62 Weight Lmt N.O.
Weighted Upper Limit - UL3 - Stopping Method determined by C03-08.
63 Phantom Flt N.O.
Stops motion based C03-10 but does not change Keypad display. RUN
L.E.D. on Display Blinks.
64 Slack Cable Enable
CLOSED Slack Cable is detection is Enabled
OPEN: Slack Cable detection is Disabled
65 Dwell Enable
Enables / Disables Dwell Function. When H01-0x = 65, OFF = Disabled.
66 Load Share
Load Share - Enables / Disabled Load Sharing.
67 Hook Height Home
Used w/ C03-14 - Height Measurement function.
68 LodShr Slave Rdy
Load Share slave drive ready signal. Loss of this signal on the master
drive while running will result in the Phantom Fault action being taken.
69 LC Bypass N.O.
Disables Load Check and clears any LC Faults.
6A LC Bypass N.C.
Disables Load Check and clears any LC Faults.
6B Brake 2 AnsrBack
Brake Answerback signal for Brake 2 Output (0AH). When programmed,
the drive will verify that brake is open before attempting to spin motor.
Drive will post BE0-2, BE4-2, BE5-2, or BE7-2 Faults or Alarms if
feedback is incorrect.
70 Torque Detection
When the input is closed, Overtorque / Undertorque detection is enabled.
73 LL2/UL2 Bypass
Bypass Upper/Lower Limit 2
74 LL/UL Bypass
Bypass Upper/Lower Limit
80 Run FWD
Forward/Up Run Command
81 Run REV
Reverse/Down Run Command
Display
Function
Содержание Impulse G+ series 4
