MacDon D65 Скачать руководство пользователя | Manualshive

Страница: 83 / 110

background image

214328

75

Revision A

5.14

Lubricating Header

5.14.1

Greasing Procedure

Greasing points are marked on machine by decals showing a grease gun and grease interval in hours of operation.
Master grease point location decals are provided on header.

DANGER

To avoid bodily injury or death from unexpected start-up of machine, always stop engine and remove key
from ignition before leaving operator

’

s seat for any reason.

1.

Wipe grease fitting with a clean cloth before greasing to avoid injecting dirt and grit.

2.

Use high temperature, extreme pressure (EP2) performance with 1% max molybdenum disulphide (NLGI
Grade 2) lithium base unless otherwise specified.

3.

Inject grease through fitting with grease gun until grease overflows fitting (except where noted).

4.

Leave excess grease on fitting to keep out dirt.

5.

Replace any loose or broken fittings immediately.

6.

Remove and thoroughly clean any fitting that will not take grease. Also clean lubricant passageway. Replace
fitting if necessary.

5.14.2

Lubrication Points

Figure 5.42: Knifehead

A - Knifehead (Single Knife - 1 Place) (Double Knife - 2 Places)

IMPORTANT:

•

To prevent binding and/or excessive wear caused by
knife pressing on guards, do

NOT

over-grease

knifehead (A).

•

Check for signs of excessive heating on first few
guards after greasing. If required, relieve some
pressure by pressing check-ball in grease fitting or
loosening the grease fitting.

•

Only 1

–

2 pumps with a mechanical grease gun is

required (do

NOT

use an electric grease gun).

•

If more than 6

–

8 pumps of grease gun are required to

fill cavity, replace seal in knifehead.

PERFORMING PREDELIVERY CHECKS

«
...
81
82
83
84
85
...
»

Содержание D65















































































































Отзывы:

Нет отзывов

Похожие инструкции для D65

Бренд: Ecco Страницы: 4

Бренд: 3M Страницы: 28

Бренд: Jacobsen Страницы: 6

Бренд: Qtx Страницы: 3

Бренд: R&S Страницы: 121

Бренд: Gaspardo Страницы: 16

Бренд: HANYOUNG NUX Страницы: 2

Ransomes HR 6010

Бренд: Jacobsen Страницы: 10

Бренд: Jacto Страницы: 64

Бренд: Additel Страницы: 107

Бренд: Sota Страницы: 7

Бренд: Raytec Страницы: 8

BIO-FIGHTER 4Xtreme

Бренд: Dust Free Страницы: 8

Бренд: HF Scientific Страницы: 5

Бренд: Lightolier Страницы: 2

Бренд: WENVY Страницы: 23

Pathport QUATTRO

Бренд: Pathway connectivity solutions Страницы: 9

Бренд: P.Lindberg Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды