MacDon D65 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 110

MacDon D65 Скачать руководство пользователя страница 45

214328

37

Revision A

Figure 4.6: Boot Engaging Header

7.

Drive windrower forward slowly so that boots (A) enter
header legs (B). Continue to drive slowly forward until
linkages contact support plates in lower header legs
and header nudges forward.

8.

Check that linkages are properly engaged in header
legs, contacting support plates.

4.1

Connecting Center-Link

The procedure for connecting the center-link varies depending on the type of center-link installed on the machine.
Refer to the applicable topic:

•

4.1.1 Mechanical Link, page 37

•

4.1.2 Hydraulic Link without Self-Alignment Kit, page 39

•

4.1.3 Hydraulic Link with Optional Self-Alignment Kit, page 42

4.1.1

Mechanical Link

The following connection procedure applies to M100, M105, M150, and M155 windrowers with a mechanical
center-link.

WARNING

To avoid bodily injury or death from unexpected startup of machine, always stop engine and remove key
before making adjustments to machine.

Figure 4.7: Mechanical Center-Link

1.

Stop engine and remove key.

2.

Loosen nut (A) and rotate barrel (B) to adjust length so
that link lines up with header bracket.

3.

Install pin (C) and secure with cotter pin.

4.

Adjust link to required length for proper header angle by
rotating barrel (B). Tighten nut (A) against barrel. A
slight tap with a hammer is sufficient.

ATTACHING HEADER TO WINDROWER

«
...
43
44
45
46
47
...
»

Содержание D65















































































































Отзывы:

Нет отзывов