manualshive.com logo in svg

MacDon D65, Инструкция по сборке, Страница: 13 / 110

Поделиться
Скачать
MacDon D65 Скачать руководство пользователя страница 13

214328

5

Revision A

2

Unloading Header

Perform all procedures in the order they are listed.

2.1

Unloading Header from Trailer

The following procedure applies when two headers are shipped on a trailer.

CAUTION

To avoid injury to bystanders from being struck by machinery, do NOT allow people to stand in
unloading area.

CAUTION

Equipment used for unloading must meet or exceed requirements specified below. Using inadequate
equipment may result in chain breakage, vehicle tipping, or machine damage.

IMPORTANT:

Forklifts are normally rated with load centered 610 mm (24 in.) from back end of forks. To obtain forklift capacity for
a load centered at 1220 mm (48 in.), check with your forklift distributor.

Figure 2.1: Minimum Lifting Capacity

A - Load Center of Gravity
B - Load Center 1220 mm (48 in.) from Back of Forks
C - Minimum Fork Length 1981 mm (78 in.)

Table 2.1 Lifting Vehicle

15

–

25 Foot

Header

30

–

40 Foot

Header

Minimum

Lifting

Capacity

2270 kg (5000 lb.)

load center (A) at

1220 mm

(48 in.) (B) from

back of forks

3178 kg (7000 lb.)

load center (A) at

1220 mm

(48 in.) (B) from

back of forks

Minimum Fork

Length (C)

1981 mm (78 in.)

To unload headers from a trailer, follow these steps:

1.

Move trailer into position and block trailer wheels.

2.

Lower trailer storage stands.

IMPORTANT:

Avoid lifting second header and ensure forks do not interfere with shipping frame. If forks contact second
header, damage to headers may occur.

Содержание D65















































































































Отзывы:

Нет отзывов