MacDon D65 Скачать руководство пользователя страница 48

Страница: 48 / 110

214328

Revision A

Figure 4.13: GSL

A - HEADER TILT DOWN Switch

B - HEADER TILT UP Switch

CAUTION

Check to be sure all bystanders have cleared the area.

Start engine and activate HEADER TILT switches on
ground speed lever (GSL) to extend or retract center-
link cylinder so that hook lines-up with header
attachment pin.

Stop engine.

Figure 4.14: Center-Link

Push down on rod end (B) of link cylinder (A) until hook
engages pin on header and is locked.

IMPORTANT:

Hook release must be down to enable self-locking
mechanism. If release is up (open), manually push it
down after hook engages header pin.

Check that center-link (A) is locked onto header by
pulling upward on rod end (B) of cylinder.

Figure 4.15: GSL

CAUTION

Check to be sure all bystanders have cleared the area.

Start engine.

Raise header fully with HEADER UP switch (A) on
the GSL.

Stop engine and remove key.

10. Engage safety props on both lift cylinders.

ATTACHING HEADER TO WINDROWER

Содержание D65















































































































Результаты поиска

Содержание D65

Отзывы:

MacDon D65, Инструкция по сборке, Страница: 48 / 110

Результаты поиска

Содержание D65

Отзывы: