MacDon D65 Скачать руководство пользователя страница 62

Страница: 62 / 110

214328

Revision A

5.5

Checking and Adjusting Non-Timed Knife Drive Belt Tension

This procedure applies to single- and double-knife headers with non-timed knife drives.

Figure 5.6: Knife Drive (Left Shown

–

Right

Opposite)

Shut down windrower and remove key from ignition.

Open endshield(s). Refer to

3.3 Opening Endshield,

page 25

NOTE:

The knife drive is identical on both sides of the header
for double-knife headers.

Apply a force of 90 N (20 lbf) to midspan (A) of belt. The
belt should deflect 18 mm (3/4 in.). If necessary, adjust
tension as per the following steps.

IMPORTANT:

To prolong belt and drive life, do

NOT

over-tighten belt.

Figure 5.7: Knife Drive (Left Shown

–

Right

Opposite)

Loosen two bolts (A) that secure motor assembly to
header endsheet.

Turn adjuster bolt (B) as required to move drive motor
to achieve belt deflection as per above. Tighten
bolts (A).

Ensure that clearance between belt (C) and belt
guide (E) is 1 mm (1/32 in.).

Loosen three bolts (D), and adjust position of guide (E)
as required.

Tighten bolts (D).

Close endshield(s). Refer to

3.7 Closing Endshield,

page 29

NOTE:

Readjust tension of a new belt after a five hour run-in
period.

PERFORMING PREDELIVERY CHECKS

Содержание D65















































































































Результаты поиска

Содержание D65

Отзывы:

MacDon D65, Инструкция по сборке, Страница: 62 / 110

Результаты поиска

Содержание D65

Отзывы: