MacDon D65 Скачать руководство пользователя страница 27

Страница: 27 / 110

214328

Revision A

Figure 3.5: Lifting Double Reel

Double reel:

Position sling (A) around reel tube near

reel center support arm. Raise lifting device to relieve
load on shipping supports.

Figure 3.6: Reel Arm Braces

Double reel:

Lift reel to gain access to center lift

cylinder.

10.

Double reel:

Remove shipping wire and banding from

reel center lift cylinder. Remove socket head bolt and
nut from cylinder rod.

11.

Double reel:

Lift reel so that hole in lift cylinder rod

lines up with mounting hole (A) in reel arm.

12.

Double reel:

Attach rod end of cylinder to reel arm with

socket head bolt and nut (A). Access hardware through
holes in reel arm braces (C).

13.

Double reel:

Torque bolt and nut (A) to 54

–

61 Nm

(40

–

45 lbf·ft).

14.

Double reel:

Remove pin at barrel end of cylinder.

15.

Double reel:

Adjust reel height so pin (B) can be

installed at barrel end of cylinder and mounting
structure.

Figure 3.7: Left End Reel Lift

16. Reposition sling (A) around reel tube near opposite

outboard reel arm.

17. Remove shipping wire and banding from reel lift

cylinder.

ASSEMBLING HEADER

Содержание D65















































































































Результаты поиска

Содержание D65

Отзывы:

MacDon D65, Инструкция по сборке, Страница: 27 / 110

Результаты поиска

Содержание D65

Отзывы: