MacDon D65 Скачать руководство пользователя страница 73

Страница: 73 / 110

214328

Revision A

Figure 5.27: Cam Disc Positions

Turn the latch pin (A) counterclockwise using a 3/4 in.
wrench to release the cam disc.

Use the wrench on bolt (B) to rotate the cam disc and
align the latch pin (A) with the desired cam disc hole
position (C) (1 to 4).

NOTE:

Bolt (B) is positioned through the cam disc (transparent
view shown in illustration for improved clarity).

Turn the latch pin (A) clockwise to engage and lock the
cam disc.

Repeat the above procedure for the opposite reel.

IMPORTANT:

Ensure the cam is secured into position before
operating the machine.

5.9.2

Measuring Reel Clearance

DANGER

To avoid bodily injury or death from unexpected start-up or fall of raised machine, always stop engine,
remove key, and engage safety props before going under header for any reason.

Park machine on level ground.

Figure 5.28: Fore-Aft Position

Set fore-aft position to middle position 5 on fore-aft
position indicator decal (A).

Lower reel fully.

Shut down engine and remove key from ignition.

PERFORMING PREDELIVERY CHECKS

Содержание D65















































































































Результаты поиска

Содержание D65

Отзывы:

MacDon D65, Инструкция по сборке, Страница: 73 / 110

Результаты поиска

Содержание D65

Отзывы: