MacDon D65 Скачать руководство пользователя страница 3

Страница: 3 / 110

Introduction

This instruction manual describes the unloading, setup, and predelivery requirements for the MacDon D65 Draper
Header for Windrowers.

To ensure your customers receive the best performance and safety from this product, carefully follow the unload
and assembly procedure from the beginning through to completion.

Some sections/steps apply to multiple header configurations and sizes. Refer to instructions for your specific
header.

Carefully read all the material provided before attempting to unload, assemble, or use the machine.

Retain this instruction for future reference.

NOTE:

Keep your MacDon publications up-to-date. The latest version can be downloaded from our website
(

www.macdon.com

) or from our Dealer portal (

https://portal.macdon.com

) (login required).

This instruction is available in the English language only.

214328

Revision A

Содержание D65















































































































Результаты поиска

Содержание D65

Отзывы:

MacDon D65, Инструкция по сборке, Страница: 3 / 110

Результаты поиска

Содержание D65

Отзывы: