MacDon D65 Скачать руководство пользователя страница 41

Страница: 41 / 110

214328

Revision A

3.11

Adding Tire Ballast

When using large headers on windrower, adding fluid ballast to rear caster tires will improve machine stability.

Machine stability is also affected by different attachments, windrower options, terrains, and driving techniques.

Ballast capability per tire is at a maximum fill of 75% or when fluid is level with valve stem when stem is positioned
at 12 o

’

clock position. Always add an equal amount of fluid on both sides. Fluid can be added to any level up to

maximum fill.

Table 3.1 Fluid per Tire

Tire Size

Fluid per Tire at 75% Fill

liters (U.S. Gal.)

Total Weight of Both Tires

kg (lb.)

7.5 x 16

38 (10)

91 (200)

10 x 16

69 (18)

170 (380)

16.5 x 16.1

158 (41)

377 (830)

Table 3.2 Recommended Ballast

Header Size and Type

Applicable

Windrower

Recommended

Tire Size

Recommended Ballast

Level Ground

Hills

Per Tire

liters

(U.S. Gal.)

Both Tires

kg (lb.)

Per Tire

liters

(U.S. Gal.)

Both Tires

kg (lb.)

25 ft.

and less

All

7.5 x 16

10 x 16

16.5 x 16.1

30 ft. Single Reel

or Double Reel

(without conditioner)

35 ft. Single Reel

All

7.5 x 16

10 x 16

16.5 x 16.1

38 (10)

91 (200)

30 ft. Double Reel

(with steel fingers and

conditioner)

35 ft. Double Reel

(5- or 6-bat)

All

Level ground:

10 x 16

16.5 x 16.1

Hills:

16.5 x 16.1

69 (18)

170 (380)

115 (30)

288 (630)

40 ft.

M150
M200

M155

M205

16.5 x 16.1

115 (30)

288 (630)

158 (41)

377 (830)

When recommended fluid ballast has been added, proceed to

5 Performing Predelivery Checks, page 49

ASSEMBLING HEADER

Weights given are for typical calcium chloride and water mixtures. Weight is reduced by 20% if only water is
used (for areas that do not require antifreeze protection).

If only water is used, increase volume of water by 20% (up to maximum allowable fill per tire) to compensate.

Содержание D65















































































































Результаты поиска

Содержание D65

Отзывы:

MacDon D65, Инструкция по сборке, Страница: 41 / 110

Результаты поиска

Содержание D65

Отзывы: