MacDon D65 Скачать руководство пользователя страница 107

Страница: 107 / 110

214328

Revision A

Predelivery Checklist

Perform these checks and adjustments prior to delivery to your Customer.

Adjustments are normally not

required as the machine is factory-assembled and adjusted.

If adjustments are required, refer to the

appropriate page number in this manual. The completed Checklist should be retained by either Operator or Dealer.

CAUTION

Carefully follow the instructions given. Be alert for safety related messages that bring your attention to
hazards and unsafe practices.

Header Serial Number:

Table .16 D65 Predelivery Checklist

–

North America

Item

Reference

Check for shipping damage or missing parts. Be sure all
shipping material is removed.

—

Check for loose hardware. Tighten to required torque.

7.1 Torque Specifications, page 85

Check tire pressure (Transport/Stabilizer Option).

5.2 Checking Transport/Stabilizer Tire Pressure,
page 51

Check wheel bolt torque (Transport/Stabilizer Option).

5.3 Checking Wheel Bolt Torque, page 52

Check knife drive box breather position.

5.4 Checking Knife Drive Box, page 53

Check knife drive box lube level.

5.4 Checking Knife Drive Box, page 53

Check knife drive belt(s) tension.

5.6 Checking and Adjusting Timed Double-Knife
Drive Belt Tension, page 55
5.5 Checking and Adjusting Non-Timed Knife
Drive Belt Tension, page 54

Check reel is centered between header endsheets.

5.8 Centering Reel, page 62

Check reel tine to cutterbar clearance.

5.9 Measuring and Adjusting Reel Clearance to
Cutterbar, page 64

Check draper tension.

5.10 Checking and Adjusting Draper Tension,
page 68

Check draper seal.

5.11 Checking Draper Seal, page 71

Check knife hold-down adjustment.

5.7 Checking and Adjusting Knife Hold-Downs,
page 57

Check skid shoes are evenly adjusted an appropriate
setting for first crop.

5.1 Checking and Adjusting Skid Shoes, page 49

Check fit of endshields.

5.13 Checking and Adjusting Endshields, page
74

Check that header is level.

5.12 Leveling Header, page 73

Grease all bearings and U-joints.

5.14 Lubricating Header, page 75

Check entire machine for shipping wires or strapping and
remove.

—

Содержание D65















































































































Результаты поиска

Содержание D65

Отзывы:

MacDon D65, Инструкция по сборке, Страница: 107 / 110

Результаты поиска

Содержание D65

Отзывы: