MacDon D65 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 110

MacDon D65 Скачать руководство пользователя страница 72

214328

64

Revision A

5.9

Measuring and Adjusting Reel Clearance to Cutterbar

The minimum clearance between reel fingers and cutterbar ensures that reel fingers do not contact cutterbar during
operation. The clearance is set at the factory, but some adjustment may be necessary before operation or if there is
evidence of contact during operation.

The finger to guard/cutterbar clearances with reel fully lowered are shown in Table

Figure 5.25: Finger Clearance

Table 5.2 Finger to Guard/Cutterbar Clearance

Header Width

(X) +/- 3 mm (1/8 in.) at Reel Ends

Single Reel

Double Reel

15 ft.

20 mm (3/4 in.)

–

20 ft.

20 mm (3/4 in.)

–

25 ft.

25 mm (1 in.)

–

30 ft.

45 mm (1-3/4 in.)

20 mm (3/4 in.)

35 ft.

60 mm (2-3/8 in.)

20 mm (3/4 in.)

40 ft.

–

20 mm (3/4 in.)

5.9.1

Checking and Adjusting Reel Cam

DANGER

To avoid bodily injury or death from unexpected start-up of machine, always stop engine and remove key
from ignition before leaving operator

’

s seat for any reason.

Figure 5.26: Cam Disc Center Reel Arm Dual
Reel Only

1.

Ensure reel cam latch pin (A) is in the same cam
position (B) at both the center cam disc and right cam
disc (not shown). If latch pin position is not the same on
both cams, proceed to Step

to adjust reel

cam position.

PERFORMING PREDELIVERY CHECKS

«
...
70
71
72
73
74
...
»

Содержание D65















































































































Отзывы:

Нет отзывов