MacDon D65 Скачать руководство пользователя страница 82

Страница: 82 / 110

214328

Revision A

5.13

Checking and Adjusting Endshields

Plastic endshields are subject to expansion or contraction caused by large temperature variations. The position of
top pin and lower catch can be adjusted to compensate for dimensional changes.

Figure 5.40: Gap Between Endshield and
Header Frame

Check gap (X) between front end of shields and header
frame and compare to values in Table

5.4, page 74

Table 5.4 Endshield Gap at Various Temperatures

Temperature °C (°F)

Gap (X) mm (in.)

−

4 (25)

28 (1

–

1/10)

7 (45)

24 (1)

18 (65)

20 (13/16)

29 (85)

16 (5/8)

41 (105)

12 (1/2)

52 (125)

8 (5/16)

63 (145)

4 (3/16)

89 (165)

NOTE:

If endshield gap is correct, skip to next procedure. If
adjustment is required, follow these steps:

Figure 5.41: Endshield Adjustment

Open endshield. Refer to

3.3 Opening Endshield, page

Loosen nut (A) on pin (B) from inside endsheet.

Close endshield and adjust position to achieve desired
gap between front end of shield and header frame in
accordance with Table

5.4, page 74

Open endshield and tighten nut (A).

Check for a snug fit between top of shield and header
frame, and for full engagement of endshield on pin (B).

If necessary, loosen bolts on catch (C) and adjust catch
as required to reposition shield.

Tighten bolts on catch (C).

Close endshield. Refer to

3.7 Closing Endshield, page

PERFORMING PREDELIVERY CHECKS

Содержание D65















































































































Результаты поиска

Содержание D65

Отзывы:

MacDon D65, Инструкция по сборке, Страница: 82 / 110

Результаты поиска

Содержание D65

Отзывы: