LXNAV LX80xx страница 112 Скачать руководство пользователя

Страница: 112 / 192

Operating Modes

Version 6.03, May 2017

Page 112 of 192

Use

PAGE>>

button to toggle between different pages.

5.4.2.1

General statistics

Using the PAGE selector knob the user can change the statistics subpage.

There are three subpages available:



Flight statistics

displays data for whole flight.

Dis.flown

is the optimised distance.

XC speed is average speed corrected for altitude difference.

Average vario

is used in

this calculation.



Task statistics

displays data for the started task. Distance flown is the distance that

has already been flown on the task.



The

last 60 minutes

statistics displays data for the last 60 minutes of flight. If the

task was started then

Dis.flown

is the distance flown on the task for the last hour

otherwise it is the optimised distance. If the task distance is used a remark (On Task) is

displayed in the header.

5.4.2.2

Detailed task statistics

Using the PAGE selector knob the user can select different task points. Press

VIEW

button

to show more details for selected leg.

Содержание LX80xx

































































































































































































Результаты поиска

Содержание LX80xx

Отзывы:

Похожие инструкции для LX80xx

Бренды по названию

Популярные бренды

LXNAV LX80xx, Руководство пользователя

Результаты поиска

Содержание LX80xx

Отзывы:

Похожие инструкции для LX80xx

Бренды по названию

Популярные бренды