LXNAV LX80xx страница 30 Скачать руководство пользователя

Страница: 30 / 192

Operating Modes

Version 6.03, May 2017

Page 30 of 192

5.1

Setup Mode

In the setup menu users can configure the main display unit and connected devices. Turn

the bottom-right knob - PAGE selector - or press the UP/DOWN arrow on the remote stick to

select the appropriate setup item. Turn the bottom-left knob - ZOOM selector - or press the

LEFT/RIGHT arrow on the remote stick to move faster over menu. Press the

SELECT

button or push middle multi-directional button on the remote stick to enter a menu. A

dialogue or sub-menu will open.

The setup menu is slightly different on the rear seat device as not all options are applicable.

Items which are marked with an asterisk (*) are available only in the front seat

setup menu.

5.1.1

QNH and RES

Turn the bottom-right knob to select the required entry field. Press the

EDIT

button and

start editing the value.

5.1.1.1

QNH*

Using this feature it is possible to offset the altitude datum which could have changed due

to pressure changes during the flight. Since changing the QNH influences the indicated

Содержание LX80xx

































































































































































































Результаты поиска

Содержание LX80xx

Отзывы:

Похожие инструкции для LX80xx

Бренды по названию

Популярные бренды

LXNAV LX80xx, Руководство пользователя

Результаты поиска

Содержание LX80xx

Отзывы:

Похожие инструкции для LX80xx

Бренды по названию

Популярные бренды