LXNAV LX80xx Скачать руководство пользователя страница 189

Страница: 189 / 192

Options

Version 6.03, May 2017

Page 189 of 192

10.4.2

Installation

For more detailed instructions on installation, please refer to installation manual.

Remote stick is connected to RS485 bus through RS485 splitter. Be careful to connect

correct coloured wire to pin, which is marked with same colour.

PTT wires are connected to radio push to talk input and SC wire is connected to Speed to fly

input of vario unit.

Do not forget to set the speed command input setting to TASTER (see

Chapter 5.1.11.1).

After installation there is no special setting required on main display unit as the

remote stick will be automatically detected.

10.5

Compass

Compass module must be connected to RS485 bus. It must be installed to the place where

is no strong magnetic fields (Irons or ferromagnetic materials), cables with AC current or not

constant DC currents.

When installing magnetic compass use screws made of non-ferromagnetic
materials (plastic or brass)

Orientation of compass module marked on housing as on picture above.

Содержание LX80xx

































































































































































































Результаты поиска

Содержание LX80xx

Отзывы:

LXNAV LX80xx, Руководство пользователя, Страница: 189 / 192

Результаты поиска

Содержание LX80xx

Отзывы: