LXNAV LX80xx Скачать руководство пользователя страница 91

Страница: 91 / 192

Operating Modes

Version 6.03, May 2017

Page 91 of 192

Compass will be enabled if check box

Enable compass

is ticked. If you would like to

perform in-flight calibration, check

Enable in-flight calibration

. It is not recommended to

do in-flight calibration in very turbulent conditions.

Press

ALIGN

button to align compass with AHRS, which is built-in V9/V8/V80 vario. When

installing compass, please make sure to align it as much as possible with V9/V8/V80

variometer. Deviation of few degrees is tolerated. When aligning compass with AHRS it is

important that cabin is closed and glider is not moving. Message will be displayed on screen,

when aligned.

Press

CALIB

button to start calibration of compass on the ground. Calibration process I very

straightforward. Make sure glider fuselage is levelled (use tail dolly), wings are levelled and

canopy is closed with pilot inside. Switch on all the avionics, which is normally switched on

while flying. Confirm calibration of compass to start calibration process. Assistant on the

wing should slowly rotate glider with wings levelled.

Содержание LX80xx

































































































































































































Результаты поиска

Содержание LX80xx

Отзывы:

LXNAV LX80xx, Руководство пользователя, Страница: 91 / 192

Результаты поиска

Содержание LX80xx

Отзывы: