Lennox Baltic BCK 020 Скачать руководство пользователя страница 97

Страница: 97 / 110

Page 96 - IOM / ROOFTOP BALTIC Series - 0

03 - E

maintenance diagnostic

FAULT

Heat Pump mode:
Circuit breaker
open

POSSIBLE CAUSE AND SYMPTOMS

High Amps due to a low voltage from the main
supply

High amps due to freezing of the coil

Flexy: Water ingress in the motor connection box.

SOLUTION

Check the voltage drop when all components
are running.
Change the circuit breaker for one with a higher
rating.

Check the adjustable amps on the motor starter.
Adjust the defrost cycle set points.

Change the component

OUTDOOR AXIAL FAN

FAULT

High Temperature
trip out on electric
heater

POSSIBLE CAUSE AND SYMPTOMS

Low airflow rate

Incorrect position of the Klixon

SOLUTION

Measure and estimate the airflow and pressure
and compare with the specification from
customer.

Check that the Klixon, is positioned in the
airflow, relocate Klixon if necessary
Check that there is no heat transfer from the
Klixon support.

ELECTRIC HEATER

FAULT

Water found in the
ventilation section

Water ingress in
the filter
compartment

POSSIBLE CAUSE AND SYMPTOMS

Cooling mode:
Water carried away from the coil because of
excessive airflow and speed on the coil.

Low air pressure in the compartment due to a
high airflow rate or a high pressure drop before
the fan

Check seals around the ventilation section.

Water ingress through a leaking fresh air hood or
when running 100% fresh air

SOLUTION

Estimate the airflow rate and check the speed is
lower than 2.8 m/s

Check filter
Reduce airflow rate

Check the door seal
Check for the presence of silicone seals in the
corners of the door and at the bottom of the
refrigeration section bulkhead.

Check the seals and flanges in the fresh air
hood
Reduce the airflow rate if necessary

ELECTRIC HEATER

Содержание Baltic BCK 020















































































































Результаты поиска

Содержание Baltic BCK 020

Отзывы:

Похожие инструкции для Baltic BCK 020

Бренды по названию

Популярные бренды

Lennox Baltic BCK 020, Руководство по установке, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание Baltic BCK 020

Отзывы:

Похожие инструкции для Baltic BCK 020

Бренды по названию

Популярные бренды