manualshive.com logo in svg

Lennox Baltic BCK 020, Руководство по установке, эксплуатации и техническому обслуживанию

Lennox Baltic BCK 020 - ультраэффективный котел для вашего дома. На нашем сайте вы можете скачать бесплатно Руководство по монтажу, эксплуатации и техническому обслуживанию. Скачайте его с manualshive.com прямо сейчас и наслаждайтесь комфортом и экономией энергии вашего дома.

Поделиться
Скачать
background image

Page 2 - IOM  / ROOFTOP BALTIC Series - 0

8

03 - E

CONTENTS

INSTALLATION

TRANSPORT - HANDLING ......................................................................................... 4
DIMENSIONS AND WEIGHTS ....................................................................................5
LIFTING THE UNITS ................................................................................................... 6
PRELIMINARY CHECKS .............................................................................................7
MINIMUM CLEARANCE AROUND THE UNIT ............................................................8
INSTALLATION ON ROOF MOUNTING FRAMES ......................................................9
Adjustable roofcurb ....................................................................................................10
Multidirectional roofcurb ............................................................................................16
Non-adjustable Non-assembled roofcurb ..................................................................22
Curbing and flashing ..................................................................................................25
ECONOMISER AND EXTRACTION ..........................................................................26

COMMISSIONING

27

BEFORE CONNECTING THE POWER ....................................................................27
CLIMATIC ..................................................................................................................27
POWERING THE UNIT .............................................................................................28
RUN TEST .................................................................................................................28

COMMISSIONING SHEET

29

VENTILATION

30

BELT TENSION .........................................................................................................32
MOUNTING & ADJUSTING PULLEYS ......................................................................33
AIRFLOW BALANCING ............................................................................................34
FILTERS ....................................................................................................................40
FAN STARTER ..........................................................................................................41

HEATING OPTIONS

42

HOT WATER COILS ..................................................................................................42
ELECTRIC HEATER ..................................................................................................44
GAS BURNERS .........................................................................................................45

CLIMATIC CONTROLLER

55

COMMUNICATION LINKS .........................................................................................56
SOFTWARE FEATURES AND LOGIC ......................................................................57
OTHER FEATURES ..................................................................................................59
CONTROL INTERFACES ..........................................................................................60
DC50 COMFORT DISPLAY .......................................................................................60
DS50 SERVICE  DISPLAY ........................................................................................62
DS50 MENU TREE ....................................................................................................64
SAFETY AND ERROR CODES .................................................................................73
COMMISSIONING .....................................................................................................74

CONTROL INTERFACE CLIMALINK-CLIMALOOK

75

ELECTRICAL WIRING DIAGRAM

83

REFRIGERATION CIRCUIT

93

MAINTENANCE DIAGNOSTIC

95

MAINTENANCE PLAN

98

CONTENTS

Содержание Baltic BCK 020















































































































Отзывы:

Нет отзывов

Похожие инструкции для Baltic BCK 020

Panasonic CW-XC83YU Install And Operation Instructions preview
CW-XC83YU
Бренд: Panasonic Страницы: 27
Panasonic CS-TE15HKE Service Manual preview
CS-TE15HKE
Бренд: Panasonic Страницы: 56
Panasonic U-36LE1U6 Installation Instructions Manual preview
U-36LE1U6
Бренд: Panasonic Страницы: 48
Panasonic S-60PT2R5A Operating Instructions Manual preview
S-60PT2R5A
Бренд: Panasonic Страницы: 12
Panasonic CS-RZ25WKRW Operating Instructions Manual preview
CS-RZ25WKRW
Бренд: Panasonic Страницы: 20
Panasonic CS-RE9JKR Operating Instructions Manual preview
CS-RE9JKR
Бренд: Panasonic Страницы: 10
Panasonic CS-MKS9NB4U Installation Instructions Manual preview
CS-MKS9NB4U
Бренд: Panasonic Страницы: 18
Panasonic CS-MKS7NKU Installation Manual preview
CS-MKS7NKU
Бренд: Panasonic Страницы: 14
Panasonic S-45MK2E5A Operating Instructions Manual preview
S-45MK2E5A
Бренд: Panasonic Страницы: 112
Danby DAP290BAW Owner'S Manual preview
DAP290BAW
Бренд: Danby Страницы: 28
REMKO RXW 261 User Manual preview
RXW 261
Бренд: REMKO Страницы: 24
Dutch originals DO-CH-ACL150DRT User Manual preview
DO-CH-ACL150DRT
Бренд: Dutch originals Страницы: 48
DayRelax XQS140UY1 User Manual preview
XQS140UY1
Бренд: DayRelax Страницы: 100
Airwell K 12 DCI Service Manual preview
K 12 DCI
Бренд: Airwell Страницы: 94
Daikin UAT150C Technical Manual preview
UAT150C
Бренд: Daikin Страницы: 36
Liebert Mini-Mate2 MCD24A User Manual preview
Mini-Mate2 MCD24A
Бренд: Liebert Страницы: 80
ARDES AR5R11 Instructions For Use Manual preview
AR5R11
Бренд: ARDES Страницы: 20
Vaillant V 10-025 NHI Training Manual preview
V 10-025 NHI
Бренд: Vaillant Страницы: 56

Бренды по названию

Популярные бренды

Загрузить еще бренды