Lehner Lifttechnik OMEGA-F страница 34 Скачать руководство пользователя

Страница: 34 / 53

OMEGA

Installation Manual

Edition February

2020

Omega

platform lift

page 34 of 52

Contactor
feedback

20 (5.)

Ride to the next
stop position

The contacts of the ride contactors
(K50, K51) or the safety relay KSK
have not dropped off after completion
of a ride.

Approach from the stop position is no
longer possible unless the correct
signal (depending on the setting in
contactor feedback) is present.

Data exchange
between drive
and platform
board

21 (6.)

Ride is
interrupted

Communication via the rope did not
work.

Identified on the drive side.

WDTO occurred
drive

22 (7.)

Ride is
interrupted

Contact manufacturer!

(Watchdog timer timeout occurred)

SWR occurred
drive

23 (8.)

Ride is
interrupted

Contact manufacturer!

(Software reset occurred)

BOR occurred
drive

24 (9.)

Ride is
interrupted

This error occurs with a very short
power failure.

Internal FI error

25 (A.)

Ride is
interrupted

Indicates if an internal error has
occurred in the drive. Troubleshoot
the error in the FI error list according
to the FI display (Page 387).

FI overcurrent

26 (B.)

Ride is
interrupted

Overcurrent has occurred at the
drive. Check motor or check for short
circuit.

SPI timeout
platform

112 (-)

Ride is
interrupted

The communication between the PIC
microcontroller and the Echelon
Powerline module was faulty.
Powerline module defective.

Data exchange
between drive
and platform
board

113 (-)

Ride is
interrupted

Communication via the rope did not
work.

Platform sends data to the drive and
does not get a correct response.

Possible Cause: Failure of the
voltage regulator (24V) on the drive
board due to overheating.

Содержание OMEGA-F






















































Результаты поиска

Содержание OMEGA-F

Отзывы:

Похожие инструкции для OMEGA-F

Бренды по названию

Популярные бренды

Lehner Lifttechnik OMEGA-F, Руководство по установке

Результаты поиска

Содержание OMEGA-F

Отзывы:

Похожие инструкции для OMEGA-F

Бренды по названию

Популярные бренды