Lehner Lifttechnik OMEGA-F страница 23 Скачать руководство пользователя | Manualshive

Страница: 23 / 53

background image

OMEGA

Installation Manual

Edition February

2020

Omega

platform lift

page 23 of 52

Explanation of the menu

To enter the menu, both the up and the down directional button on the handset need to be
pressed for more than 5 seconds. The display then shows always 2 menu items. The upper
item in the display is always the active one. With the upward directional button it can be
changed between the main items. With the downward (enter) button an item directory can
be entered. A parameter value can be changed with the upward directional button and then
be confirmed with the downward button on the handset.

Generally all functions are set according to the order specifications. The only item that has
to be adjusted on site is the change of drive speed in the menu item “Teach-in Start”. Below
all items are explained in greater detail. The standard parameter is hereby underlined.

Language

If the predefined language is not wanted please first adjust the required menu language.

Error

20 different errors can be determined and read.

Menu item

Parameter

Meaning

Description

Error list

-

-

This shows a list of the error that
occurred.

Clear errors

-

-

Deletes list of errors

Acknowledge error

With this function the present failure will be deleted and the function of the lift will be
restored if the error was eliminated. Errors can only be acknowledged when the platform is
in a landing station. This can be done either by the use of the menu item “acknowledgement
of errors” or with the button S1 on the drive unit control.
If an error can not be acknowledged it means that the error is still persisting. For example if
the thermostat relay of the motor is active the error can only be acknowledged when the
motor cooled down and the relay is released. The errors with light blue background in the
error table above are automatically acknowledged in a landing station!
If the 7 segment display is still blinking and the display still shows an error message then the
error is still persistent and cannot be acknowledged.

Menu item

Parameter

Meaning

Description

Language

GER

German

Language to be chosen

ENG

English

CZE

Czech

ESP

Spanish

FRA

French

«
...
21
22
23
24
25
...
»

Содержание OMEGA-F






















































Отзывы:

Нет отзывов

Похожие инструкции для OMEGA-F

Бренд: Jefferson Страницы: 24

Бренд: Absima Страницы: 5

Бренд: Sure Heat Страницы: 10

GALA TIG 3200 ACDC

Бренд: GALAGAR Страницы: 4

Бренд: IDEAL Страницы: 23

Бренд: National Instruments Страницы: 21

Ostrich Eggbot 2.0

Бренд: Evil Mad Scientist Страницы: 45

Бренд: Clarke Страницы: 16

Бренд: Lincoln Electric Страницы: 23

Бренд: Parweld Страницы: 20

Бренд: B&R Industries Страницы: 2720

Бренд: BREWISTA Страницы: 2

Бренд: JCM Страницы: 11

750-1417/040-000

Бренд: WAGO Страницы: 58

Бренд: TECNOMAGNETE Страницы: 26

OXeN X2-E-1.2-V

Бренд: SIRE Страницы: 19

Бренд: Interlift Страницы: 18

Бренд: Abicor Binzel Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды