Lehner Lifttechnik OMEGA-F Скачать руководство пользователя страница 33

Страница: 33 / 53

OMEGA

Installation Manual

Edition February

2020

Omega

platform lift

page 33 of 52

Motor
temperature

Fire alarm contact
(optional)

13 (d)

Ride to the next
stop position

The thermal contact in the drive
motor has tripped or the fire alarm
contact has tripped (optional).

An approach from the stop position is
no longer possible as long as the
signal is present.

Short circuit
between traction
rope and tube

14 (E)

Ride to the next
stop position,
provided that the
short circuit is no
longer present

This error occurs if there is still a
short circuit between the traction
rope and the tube after five restart
attempts.

An approach from the stop position is
no longer possible as long as the
signal is present.

Short circuit
between support
rope and tube

15 (F)

Ride to the next
stop position

When a short circuit occurs between
the support rope and the tube.

An approach from the stop position is
no longer possible as long as the
signal is present.

This error also occurs when the
resistor RV on the platform is not
properly connected or has a
resistance of about 50 ohms.

Following error Safety switch
triggered



Rocker makes short

circuit

SPI timeout drive

16 (1.)

Ride is
interrupted

The communication between the PIC
microcontroller and the Echelon
Powerline module was faulty.
Powerline module defective.

Safety circuit

17 (2.)

Ride to the next
stop position

Safety Circuit Relay on platform
board (KFahrAUF1, KFahrAB1)
Contact is stuck.

FI communication 18 (3.)

Only slow ride

The communication with the
frequency inverter via the RS485
interface (Modbus) has failed.

Communication
with EEPROM
drive

19 (4.)

The communication of the
microcontroller with the EEPROM
located on the drive board failed, or
memory location in EEPROM could
not be written correctly.

Содержание OMEGA-F






















































Результаты поиска

Содержание OMEGA-F

Отзывы:

Похожие инструкции для OMEGA-F

Бренды по названию

Популярные бренды

Lehner Lifttechnik OMEGA-F, Руководство по установке

Результаты поиска

Содержание OMEGA-F

Отзывы:

Похожие инструкции для OMEGA-F

Бренды по названию

Популярные бренды