manualshive.com logo in svg

Lehner Lifttechnik OMEGA-F, Руководство по установке, Страница: 35 / 53

Поделиться
Скачать
Lehner Lifttechnik OMEGA-F Скачать руководство пользователя страница 35

 

OMEGA

 Installation Manual 

Edition February 

2020 

 

Omega

 platform lift 

page 35 of 52 

Communication 
with EEPROM 
platform 

114 (-) 

- 

The communication of the 
microcontroller with the EEPROM 
located on the platform board has 
failed, or memory location in 
EEPROM could not be written 
correctly. 

WDTO occurred 
Platform 

116 (-) 

Ride is 
interrupted 

Contact manufacturer! 

(

Watchdog timer timeout occurred)

 

SWR occurred 
Platform 

117 (-) 

Ride is 
interrupted 

Contact manufacturer! 

(Software reset occurred) 

BOR occurred 
Platform 

118 (-) 

Ride is 
interrupted 

This error occurs with a very short 
power failure.  

 

If a power failure occurs on the drive or on the platform, this is indicated by information on 
the display. A power failure on the drive is equivalent to a mains failure (or main power 
switch off-on). This information is deleted when the stop position is reached. 

Power failure at drive    

 

Power-off A. (powerloss d.) 

Power failure at platform  

 

Power-off P. (powerloss p.) 

 
 
Status display in normal operation 

 
If the ride can not be started because there is no requirement (for example, emergency stop 
button pressed), it will be displayed on the platform's display during normal operation. Then 
the display appears, for example: Cause Circuit P. The status indicator is more dominant 
than an error code, i.e. If there is already an error, it will be superseded by the status 
display. 
 
The following table explains the meaning of the displayed messages. 

Problem (issue reason) 

Description 

Contact up 

(contact up) 

The drive up is prevented by the pressed contact strip or the 
pressed ascent flap. 

Contact down 

(contact down) 

The descent is prevented by the pressed contact strip or the 
pressed ascent flap. 

Safety circuit P. 

(s. circuit p) 

The ride is prevented by an interrupted safety circuit switch on 
the platform. For example: Emergency stop, S14 or S15 
pressed 

Contact base 

(safety bottom) 

The descent is prevented by the depressed contact base, i.e. 
the ascent must still be possible. 

Содержание OMEGA-F






















































Отзывы:

Нет отзывов