manualshive.com logo in svg

Lakeshore 330, Руководство пользователя, Страница: 81 / 104

Поделиться
Скачать
Lakeshore 330 Скачать руководство пользователя страница 81

Lake Shore Model 330 Autotuning Temperature Controller User’s Manual 

 

 

Options and Accessories 

6-3 

6.3 ACCESSORIES 

Accessories are devices that perform a secondary duty as an aid or refinement to the primary unit. 

 

MODEL 

NUMBER 

DESCRIPTION OF MODEL 330 ACCESSORY 

106-009 * 

Heater Output Connector (Dual Banana Jack).

 

106-233 * 

Sensor Mating Connector (Quantity 2).

 

115-006 * 

Detachable 120 VAC Line Cord.

 

2001 

RJ-11 Cable Assembly

. Four-Wire Cable Assembly with RJ-11 plugs on each end. Used with RS-232C 

Interface. Cable is 14 feet (4.6 meters) long. See Figure 6-1. 

2002 

RJ-11 to DB-25 Adapter

. Adapts RJ-11 receptacle to female DB-25 connector. Connects Model 622/647 to 

RS-232C Serial Port on rear of Customer’s computer. See Figure 6-2. 

2003 

RJ-11 to DE-9 Adapter

. Adapts RJ-11 receptacle to female DE-9 connector. Connects Model 622/647 to RS-

232C Serial Port on rear of Customer’s computer. See Figure 6-3. 

 
 
 

3003 

Heater Output Conditioner.

 A passive filter which further reduces already low Model 330 heater output noise. 

Typical insertion loss for the Model 3003 is 20 dB (at 10 µV) at line frequency, and >40 dB from double the line 
frequency up. The Model 3003 is housed in a 144 mm x 72 mm x 165 mm (5.67 x 2.84 x 6.5 inch) panel mount 
enclosure and weighs 1.6 kg (3.5 lbs). 
The Model 3003 requires no external power. Take care not to reverse the polarity of the incoming heater signal. 
An input protection diode acts as a short in case of reversed polarity. It is not necessary to use ground terminals 
provided, but sometimes it helps reduce noise. Shorting out the filter input or output while the controller driving it 
is turned on is 

not 

recommended; the Model 3003 may have a large stored charge. 

 

RM-3H1 

Half-Rack Mounting Kit for One Model 330 Temperature Controller.

 Half-length mounting panel and 

mounting ears to attach one Model 330 to a 482.6 mm (19-inch) by 88.9 mm (3.5 inch) rack mount space. 
See Figure 6-4. 

 

RM-3H1-H 

Half-Rack Mounting Kit for One Model 330 Temperature Controller with Handles.

 Half-length mounting 

panel, mounting ears, and handles to attach one Model 330 to a 482.6 mm (19-inch) by 88.9 mm (3.5 inch) 
rack mount space. See Figure 6-4. 

 

RM-3H2 

Dual Mounting Shelf for Two Model 330 Temperature Controllers.

 Mounting brackets and ears to attach 

two Model 330 Temperature Controllers side-by-side on a 482.6 mm (19-inch) by 88.9 mm (3.5 inch) rack 
mount shelf. See Figure 6-5. 

 

RM-3H2-H 

Dual Mounting Shelf for Two Model 330 Temperature Controllers with Handles.

 Mounting brackets, 

ears, and handles to attach two Model 330 Temperature Controllers side-by-side on a 482.6 mm (19-inch) by 
88.9 mm (3.5 inch) rack mount shelf. See Figure 6-5. 

8072 

IEEE-488 (GPIB) Computer Interface Interconnect Cable Assembly.

 Connects two IEEE-488 devices. The 

cable is 1 meter (3.3 feet) in length. 

8271-30 

Sensor/Heater Cable Assembly.

 For Silicon Diode &100 

Ω

 Platinum RTD Temperature Sensors. 

 

See Text 

Lake Shore Cryogenic Wire

. Lake Shore sells these types of cryogenic wire: WNC = Nichrome Heater, WSL = 

Single Strand, WQT = Quad-Twist™, WDT = Duo-Twist™, WDL = Duo-Lead, WQL = Quad-Lead™, WMW = 
Manganin, and WHD = Heavy Duty. See the Lake Shore Catalog for details. 

 
 

GAN-25 

Apiezon® “N” Grease, 25 gram Tube

. General purpose grease well-suited for cryogenic use because of its 

low viscosity. Often used to thermally anchor cryogenic sensors as well as lubricate joints and o-rings. Contains 
high molecular weight polymeric hydrocarbon additive which gives it a tenacious, rubbery consistency that 
forms a cushion between mating surfaces. 

 

IF-5 

Indium Foil (5 Pieces).

 Indium is a semi-precious non-ferrous metal, softer than lead, and extremely malleable 

and ductile. It stays soft and workable down to cryogenic temperatures. May be used as a sealing gasket for 
covers, flanges, and windows in cryogenic applications. 

 
 

HTR-25 

25 

Ω

Ω

Ω

Ω

 Cartridge Heater.

 Features precision-wound nickel-chromium resistance wire, magnesium oxide 

insulation, two solid pins, non-magnetic package, and has UL and CSA component recognition. The heater is 
25 W, 6.35 mm (0.25 inch) diameter by 25.4 mm (1 inch) long. The 25 W rating is in dead air. In cryogenic 
applications, the cartridge heater can handle many times this dead air power rating. 

 
 

HTR-50 

50 

Ω

Ω

Ω

Ω

 Cartridge Heater.

 Features precision-wound nickel-chromium resistance wire, magnesium oxide 

insulation, two solid pins, non-magnetic package, and has UL and CSA component recognition. The heater is 
25 W, 6.35 mm (0.25 inch) diameter by 25.4 mm (1 inch) long. The 25 W rating is in dead air. In cryogenic 
applications, the cartridge heater can handle many times this dead air power rating. 

119-009 * 

Model 330 User’s Manual.

  

* Accessories included with a new Model 330.

 

Содержание 330









































































































Отзывы:

Нет отзывов