Lakeshore 330 Скачать руководство пользователя страница 12

Страница: 12 / 104

Lake Shore Model 330 Autotuning Temperature Controller User’s Manual

1-4

Introduction

Table 1-2. Model 330 Specifications

Thermometry:

Number of Inputs:

Two

Sensor Types:

Model 330-1X – Silicon Diode

(Sensors Sold Separately)

Model 330-2X – Platinum RTD

Model 330-3X – GaAlAs Diode

Model 330-4X – Thermocouple

Accuracy:

Based on Model and Sensor Type (Refer to Table 1-1)

Update Rate:

Both Channels in 1 second

Precision Curve Storage:

Room for twenty 31-point Curves

Standard Response Curves:

DT-400 Series Silicon Diodes

Curve 10

DT-500 Series Silicon Diodes

DRC-D or DRC-E1

(Obsolete)

PT-100 Series Platinum RTDs

DIN 43760

Thermocouples

Ch-AuFe (0.07%), Ch-AuFe (0.03%), Type E (Chromel-Constantan), Type K

(Chromel-Alumel), and Type T (Copper-Constantan)

SoftCal:

Entered in Voltage or Temperature

Control:

Control Type:

Digital, three term PID with Autotuning

Automatic Control Mode:

P, PI, or PID control, user selectable

Manual Control Mode:

Gain (

roportional) 1-999, Reset (

ntegral) 1-999 sec.,

and Rate (

erivative) 0 - 200% (0-500 sec.)

Control Stability:

To ±2.5 mK in a properly designed system for diode

sensors (Refer to Table 1.1)

Setpoint Resolution:

0.01 K or °C below 200, least significant display digit in sensor units

Control Sensor Selection:

Front Panel

Ramp Rate:

0.1 to 99.9 K/min

Zones:

10 Zones with Setpoint, P, I, D, and Heater Range

Heater Output Type:

Variable DC Current Source

Heater Setting Resolution:

15 bits

Max. Power To Heater:

50 Watts / 25 Watts (Field Configurable)

Heater Current by Range:

High (1 A), Medium (0.3 A), and Low (0.1 A)

Heater Output Compliance:

50 V (50 W) or 25 V (25 W)

Heater Load for Full Power:

Ω

(50 W) or 25

Ω

(25 W)

Minimum Heater Load:

Ω

(50 W) or 10

Ω

(25 W)

Heater Noise:

50 µV + 0.01% of output voltage (with Optional Model 3003 Heater Output

Conditioner, heater noise is lowered by 20 dB)

Front Panel:

Display:

Two, 4.5 digit LED

Display Units:

Temperature in K or °C. Sensor units in volts (330-1X & -3X),

ohms (330-2X), or millivolts (330-4X)

Setpoint display:

Shared with control sensor

Heater output display:

20 digit LED bar graph, percent of full scale current for range

Annunciators:

Channel, units, heater range, interface mode

Temperature resolution:

0.01 below 200, 0.1 above

Sensor units resolution:

Refer to Table 1-1

Keypad:

Numeric plus special function

Computer Interfaces:

IEEE-488 Capabilities:

Complies with IEEE-488.2 SH1,AH1,T5,L4,SR1,RL1,PP0,DC1, DT0,C0,E1

Serial Interface:

300 or 1200 baud, RJ-11 connector (RS-232C electrical standard)

General:

Ambient Temperature Range:

20 to 30 °C (68 °F to 86 °F), or with reduced accuracy in range 15 °C to

35 °C (59 °F to 95 °F)

Power Requirements:

110, 120, 220, 240 VAC (+5%-10%), 50 or 60 Hz; 135 Watts

Size:

217 mm x 90 mm x 419 mm (8.5" x 3.5" x 16.5"), half-rack package

Weight:

5 kilograms (11 pounds)

User-configurable with IEEE-488 or Serial Interface only.)

Содержание 330









































































































Результаты поиска

Содержание 330

Отзывы:

Lakeshore 330, Руководство пользователя, Страница: 12 / 104

Результаты поиска

Содержание 330

Отзывы: