manualshive.com logo in svg

Lakeshore 330, Руководство пользователя, Страница: 34 / 104

Поделиться
Скачать
Lakeshore 330 Скачать руководство пользователя страница 34

Lake Shore Model 330 Autotuning Temperature Controller User’s Manual 

 

 

3-8 

Operation 

3.3 CONTROL 

FUNCTIONS 

The following front panel keyboard functions relate to Model 330 control:

 

Heater (Paragraph 3.3.1), Setpoint 

(Paragraph 3.3.2), Ramp (Paragraph 3.3.3), Autotune (Paragraph 3.3.4), Manual (PID) (Paragraph 3.3.5), and 

Zone (Paragraph 3.3.6). 

3.3.1 Heater 

This key controls 

heater ranges. Four 

heater ranges are 

available: High, 

Medium, Low, and Off. 

The indicators HIGH, 

MED, LOW, or OFF 

appear in the Control 

window to indicate the 

currently selected 

range. Once selected, 

the 20 segment 

Heater 

%

 bar-graph display 

indicates, to the 

nearest 5%, the 

percentage of heater 

current applied. 

The percentage of current reflects the percentage of full scale current applied to heater output for the selected 

range. Output changes automatically according to control parameters. The figure above shows the heater set 

to MEDium and output currently at 45% of full scale. If the controller controls a system with less than 10% 

heater output, it may be necessary to reduce the heater range. 

A 25 

Ω

 load is required to get a full 25 Watt 

power output on the 25 W setting, and a 50 

Ω

 

load is required to get a full 50 Watt power 

output on the 50 W setting. See Paragraph 

2.10 for additional heater setup details.

 

If the heater load drops below 10 

Ω

 for a 25 

W heater setting, or 35 

Ω

 for a 50 W heater 

setting, the output turns off to prevent instrument overheating. If this occurs, cycle the heater range through 

OFF to re-engage the heater.

 

Error 30 (Er30) appears if measured heater output does not match the predicted output, and the controller 

turns the heater off. Check heater resistance and test for shorts in heater wiring, then turn the heater on again. 

If the error message returns, consult the factory. 

3.3.2 

Setpoint and Control 

To change the setpoint, press the 

Setpoint

 key. If the lower display already shows setpoint, it blinks, and the 

instrument is ready for a new setpoint value. If the lower display indicates the control reading, it displays the 

current setpoint. Press 

Setpoint

 again to enter a new setpoint.

 

Enter the new setpoint with the numbered keys and decimal point in the center of the keypad. Press 

Enter

 to 

complete the operation or 

Escape

 to cancel and retain the previous value. Also use either 

s

 or 

t

 to increment 

or decrement the display by one degree. 

The setpoint on the Model 330 is limited to a resolution of 0.01 for temperatures below 200 and 0.1 for 

temperatures greater than 200. Any decimal digits entered after the 100

th

 place are ignored. If the setpoint is 

displayed in degrees Celsius or millivolts, the (+/–) key toggles the sign of the set point.

 

The setpoint is limited in temperature to the range of the curve used for control. Table 3-1 gives these 

limitations in kelvin for curves 00 through 04 and 06 thru 10.

 

The 

Control

 key quickly returns the bottom from displaying the setpoint to the Control sensor reading. 

Control

LOC

MED

K

A

K

B

Sample

Heater %

100

80

60

40

20

5

Heater is on MEDium setting

Heater % Output

is at 45%

 

Heater 
Range 

Heater 

Current 

25 W with 25 

Ω

Ω

Ω

Ω

 

Heater Power 

50 W with 50 

Ω

Ω

Ω

Ω

 

Heater Power 

HIGH 

MEDIUM

LOW 

0 to 1 A 

0 to 0.3A 

0 to 0.1 A 

25 Watts 

2.5 Watts 

0.25 Watts 

50 Watts 

5 Watts 

0.5 Watts 

Содержание 330









































































































Отзывы:

Нет отзывов