Lakeshore 330 Скачать руководство пользователя страница 52

Страница: 52 / 104

Lake Shore Model 330 Autotuning Temperature Controller User’s Manual

4-10

Remote Operation

4.3 IEEE-488/SERIAL INTERFACE COMMAND SUMMARY

The IEEE-488/Serial Interface commands are listed alphabetically in function order. There are five command

groups: Common Commands (Paragraph 4.3.2), Interface Commands (Paragraph 4.3.3), Display Commands

(Paragraph 4.3.4), Control Process Commands (Paragraph 4.3.5), and Curve Commands (Paragraph 4.3.6).

The commands are listed in the same order as shown below.

Command Function Page
Common Commands

*CLS Clear

Interface .................................... 4-11

*ESE

Set Std. Event Status Enable ............. 4-11

*ESE?

Query Std. Event Status Enable ......... 4-11

*ESR?

Query Std. Event Status Register....... 4-11

*IDN? Query

Identification............................. 4-11

*OPC

Set Operation Complete ..................... 4-11

*OPC?

Query Operation Complete................. 4-11

*RST Reset

Instrument ................................ 4-12

*SRE

Set Service Request Enable............... 4-12

*SRE?

Query Service Request Enable .......... 4-12

*STB?

Query Status Byte............................... 4-12

*TST? Query

Self-Test................................... 4-12

*WAI Wait-To-Continue ............................... 4-12

Interface Commands

ADDR Set

Address ........................................ 4-13

ADDR? Address

Query.................................... 4-13

END EOI ..................................................... 4-13

END? EOI

Query........................................... 4-13

MODE Remote

Mode ..................................... 4-13

MODE?

Remote Mode Query .......................... 4-13

TERM Terminator .......................................... 4-13

TERM? Terminator

Query................................ 4-14

Display Commands

CCHN

Set Control Channel ........................... 4-14

CCHN?

Control Channel Query ....................... 4-14

CDAT?

Control Sensor Data Query ................ 4-14

CUNI

Set Control Units ................................ 4-14

CUNI?

Control Units Query ............................ 4-14

FILT

Set Display Filter ................................ 4-15

FILT?

Display Filter Query ............................ 4-15

SCHN

Set Sample Channel........................... 4-15

SCHN?

Sample Channel Query ...................... 4-15

SDAT?

Sample Sensor Data Query................ 4-15

SUNI

Set Sample Units................................ 4-15

SUNI?

Sample Units Query............................ 4-15

Command Function Page

Control Process Commands

CLIM Control

Limit ......................................4-16

CLIM?

Control Limit Query............................4-16

GAIN Set

Gain ............................................4-16

GAIN? Gain

Query ........................................4-16

HEAT? Heater

Query .....................................4-16

RAMP Enable/Disable

Ramping...................4-16

RAMP?

Ramping Enable/Disable Query ........4-16

RAMPR

Set Ramp Rate in K/min....................4-17

RAMPR?

Ramp Rate Query..............................4-17

RAMPS?

Ramping Status Query ......................4-17

RANG Set

Range .........................................4-17

RANG? Range

Query .....................................4-17

RATE Set

Rate ............................................4-17

RATE? Rate

Query ........................................4-17

RSET Set

Reset...........................................4-17

RSET? Reset

Query ......................................4-17

SETP Set

Setpoint.......................................4-18

SETP? Setpoint

Query...................................4-18

TUNE Tune

Status .......................................4-18

TUNE? Tune

Query........................................4-18

ZONE Store

Zone.........................................4-18

ZONE? Zone

Query........................................4-18

Curve Commands

ACOMP

Set A Compensation .........................4-19

ACOMP?

A Compensation Query .....................4-19

ACUR

Set Curve for A ..................................4-19

ACUR?

Curve A Query...................................4-19

ATYPE?

A Input Type Query ...........................4-19

BCOMP

Set B Compensation .........................4-19

BCOMP?

B Compensation Query .....................4-19

BCUR

Set Curve for B ..................................4-19

BCUR?

Curve B Query...................................4-20

BTYPE?

B Input Type Query ...........................4-20

CUID?

Curve Identification Query .................4-20

CURV Curve

Set...........................................4-20

CURV?

Curve No. Information Query.............4-21

ECUR Edit

Curve..........................................4-22

FREE?

Curve Bytes Free Query....................4-22

KCUR Delete

Curve......................................4-22

SCAL SoftCal

Entry .....................................4-22

4.3.1

Command List Structure

Command Name

Brief Description of Function

Syntax of what user must input

CUNI?

Input:

Returned:

Remarks:

Control Units Query

CUNI?

K, C, V, R, or M

Used to query the unit for current control units
information. The character returned will be K for
kelvin, C for Celsius, V for Volts, R for Ohms, or
M for millivolts.

Information returned in response

to the query

Explanation and definition of

returned data

Содержание 330









































































































Результаты поиска

Содержание 330

Отзывы:

Lakeshore 330, Руководство пользователя, Страница: 52 / 104

Результаты поиска

Содержание 330

Отзывы: