Lakeshore 330 Скачать руководство пользователя страница 6

Страница: 6 / 104

Lake Shore Model 330 Autotuning Temperature Controller User’s Manual

Table of Contents

Chapter/Paragraph Title

Page

3.2.7 SoftCal ............................................................................................................................. 3-5

3.2.7.1 SoftCal

Errors ............................................................................................................... 3-5

3.2.7.2 Customer-Performed

SoftCal ....................................................................................... 3-6

3.2.7.3

Entering Voltage Values from a Lake Shore SoftCal Report........................................ 3-6

3.3 Control

Functions ................................................................................................................ 3-8

3.3.1 Heater .............................................................................................................................. 3-8

3.3.2

Setpoint and Control ........................................................................................................ 3-8

3.3.2.1

Voltage Resolution (Models 321-1X, -3X, & -4X Only)................................................. 3-9

3.3.2.2

Resistance Resolution (Model 330-2X Only)................................................................ 3-9

3.3.3 Ramp ............................................................................................................................... 3-9

3.3.4 AutoTune ......................................................................................................................... 3-9

3.3.4.1

Initial Values of PID Parameters in Autotuning Mode................................................. 3-10

3.3.4.2 Minimum

Overshoot ................................................................................................... 3-10

3.3.4.3

Minimum Time To Setpoint ........................................................................................ 3-10

3.3.4.4 Gain

Only.................................................................................................................... 3-10

3.3.5

Manual Control Settings (PID) ....................................................................................... 3-10

3.3.5.1

Setting Gain (Proportional) ......................................................................................... 3-10

3.3.5.2

Setting Reset (Integral)............................................................................................... 3-10

3.3.5.3

Setting Rate (Derivative)............................................................................................. 3-11

3.3.5.4

Effect of Temperature on Tuning Parameters............................................................ 3-11

3.3.6 Zone

Setting................................................................................................................... 3-11

3.4

Interface and Miscellaneous Functions............................................................................. 3-13

3.4.1 Baud............................................................................................................................... 3-13

3.4.2 Address.......................................................................................................................... 3-13

3.4.3 Local .............................................................................................................................. 3-13

3.4.4

Instrument Reset and Factory Default Settings ............................................................. 3-13

3.4.5

Power Up (PUP) Configuration...................................................................................... 3-14

3.5

Thermocouple Controller Operation (Model 330-4X Only) ............................................... 3-15

3.5.1 Sensor

Attachment ........................................................................................................ 3-15

3.5.2

Thermocouple Curve Selection ..................................................................................... 3-15

3.5.3

Thermocouple Compensation From Front Panel .......................................................... 3-15

3.5.4

Thermocouple Compensation From Remote Interface ................................................. 3-15

3.5.5

Internal Offset Adjustment ............................................................................................. 3-15

3.5.6 Curve

Format................................................................................................................. 3-15

4 REMOTE

OPERATION.......................................................................................................................... 4-1

4.0 General ............................................................................................................................... 4-1

4.1 IEEE-488

Interface.............................................................................................................. 4-1

4.1.1

IEEE-488 Interface Settings ............................................................................................ 4-1

4.1.2

IEEE-488 Command Structure ........................................................................................ 4-1

4.1.2.1

Bus Control Commands ............................................................................................... 4-2

4.1.2.2 Common

Commands ................................................................................................... 4-2

4.1.2.3

Interface and Device Specific Commands ................................................................... 4-2

4.1.3 Status

Registers .............................................................................................................. 4-2

4.1.3.1

Status Byte Register and Service Request Enable Register ........................................ 4-2

4.1.3.2

Standard Event Status Register and Standard Event Enable Register........................ 4-3

4.1.4

Example IEEE Setup and Program ................................................................................. 4-4

4.1.4.1

GPIB Board Installation ................................................................................................ 4-4

4.1.4.2

Run the Example QuickBasic Program ........................................................................ 4-4

4.1.5

Notes On Using the IEEE Interface ................................................................................. 4-4

4.2

Serial I/O Interface .............................................................................................................. 4-7

4.2.1

Serial Interface Hardware Configuration.......................................................................... 4-8

4.2.2

Sample BASIC Serial Interface Program......................................................................... 4-8

4.2.3

Notes On Using The Serial Interface ............................................................................... 4-8

Содержание 330









































































































Результаты поиска

Содержание 330

Отзывы:

Lakeshore 330, Руководство пользователя, Страница: 6 / 104

Результаты поиска

Содержание 330

Отзывы: