Lakeshore 330 Скачать руководство пользователя страница 15

Страница: 15 / 104

Lake Shore Model 330 Autotuning Temperature Controller User’s Manual

Introduction

1-7

1.5 HANDLING LIQUID HELIUM AND LIQUID NITROGEN

Liquid Helium (LHe) and liquid nitrogen (LN

) may be used in conjunction with the Model 330. Although LHe

and LN

are not explosive, there are certain safety considerations when handling them.

1.5.1

Handling Cryogenic Storage Dewars

Operate all cryogenic containers (dewars) in accordance with manufacturer

instructions. Safety instructions are normally posted on the side of each dewar.

Keep cryogenic dewars in a well-ventilated place, protected from the weather, and

away from heat sources. Figure 3-1 shows a typical cryogenic dewar.

1.5.2

Liquid Helium and Nitrogen Safety Precautions

Transfer LHe and LN

and operate storage dewar controls in accordance with

manufacturer/supplier instructions. During transfer, follow all safety precautions

written on the storage dewar and recommended by the manufacturer.

WARNING
• Liquid helium is a potential asphyxiant and can cause rapid suffocation

without warning. Store and use in an adequately ventilated area. DO NOT

vent the container in confined spaces. DO NOT enter confined spaces

where gas may be present unless area is well-ventilated. If inhaled,

remove to fresh air. If not breathing, give artificial respiration. If

breathing is difficult, give oxygen. Get medical attention.

• Liquid helium can cause severe frostbite to exposed body parts. DO

NOT touch frosted pipes or valves. For frostbite, consult a physician

immediately. If a physician is unavailable, warm the affected parts with water that is near body

temperature.

Two essential safety aspects of handling LHe are adequate ventilation and eye and skin protection. Although

helium and nitrogen gases are non-toxic, they are dangerous because they replace air in a normal breathing

atmosphere. Liquid helium is an even greater threat because a small amount of liquid evaporates to create a

large amount of gas. Store and operate cryogenic dewars in open, well-ventilated areas.

When transferring LHe and LN

, protect eyes and skin from accidental contact with liquid or the cold gas

issuing from it. Protect eyes with full face shield or chemical splash goggles; safety glasses (even with side

shields) are inadequate. Always wear special cryogenic gloves (Tempshield CryoGloves

or equivalent) when

handling anything that is, or may have been, in contact with the liquid or cold gas, or with cold pipes or

equipment. Wear long sleeve shirts and cuffless trousers long enough to prevent liquid from entering shoes.

1.5.3

Recommended First Aid

Post an appropriate Material Safety Data Sheet (MSDS) obtained from the manufacturer/distributor at every

site that stores and uses LHe and LN

. The MSDS specifies symptoms of overexposure and first aid.

If a person exhibits symptoms of asphyxia such as headache, drowsiness, dizziness, excitation, excessive

salivation, vomiting, or unconsciousness, remove to fresh air. If breathing is difficult, give oxygen. If breathing

stops, give artificial respiration. Call a physician immediately.

If exposure to cryogenic liquids or cold gases occurs, restore tissue to normal body temperature (98.6 °F) by

bathing it in warm water not exceeding 105 °F (40 °C). DO NOT rub the frozen part, either before or after

rewarming. Protect the injured tissue from further damage and infection and call a physician immediately.

Flush exposed eyes thoroughly with warm water for at least 15 minutes. In case of massive exposure, remove

clothing while showering with warm water. The patient should not drink alcohol or smoke. Keep warm and

rest. Call a physician immediately.

NON-

MAGNETIC

KEEP

UPRIGHT

LIQUID

HELIUM

NON-

FLAMMABLE

Figure 1-3. Cryogenic

Storage Dewar

Содержание 330









































































































Результаты поиска

Содержание 330

Отзывы:

Lakeshore 330, Руководство пользователя, Страница: 15 / 104

Результаты поиска

Содержание 330

Отзывы: