Lakeshore 330 Скачать руководство пользователя страница 55

Страница: 55 / 104

Lake Shore Model 330 Autotuning Temperature Controller User’s Manual

Remote Operation

4-13

4.3.3 Interface

Commands

ADDR

Set IEEE Address.

Input:

ADDR [address]

[address]:

An integer from 1 to 30. Address 0 and 31 are reserved.

Returned:

Nothing

Remarks:

Sets the IEEE address. The Model 330 is factory preset to 12.

ADDR?

IEEE Address Query.

Input:

ADDR?

Returned:

1 to 30.

Remarks:

Returns the current IEEE address setting. The Model 330 is factory preset to 12.

END

Set End Or Identify (EOI) Status.

Input:

END 0

END 1

Returned:

Nothing

Remarks:

Sets the EOI status:

= enabled,

= disabled. When enabled, the hardware EOI line

becomes active with the last byte of a transfer. The EOI identifies the last byte allowing for

variable length data transmissions.

END?

End Or Identify (EOI) Status Query.

Input:

END?

Returned:

Current EOI status:

= EOI enabled,

= EOI disabled.

MODE

Set Local, Remote, or Remote With Local Lockout Mode.

Input:

MODE 0

MODE 1

, or

MODE 2

Returned:

Nothing

Remarks:

Sets the Model 330 mode:

= Local Mode,

= Remote Mode,

= Remote Mode with Local

Lockout. Press the front panel

Local

key to set the Model 330 to local provided the key has

not been disabled by local lockout. The Model 330 powers up in local mode.

Example:

At the end of a command string,

MODE 0

maintains constant local operation.

MODE?

Mode

Query.

Input:

MODE?

Returned:

Current mode setting:

= local mode,

= remote mode,

= remote mode with local lockout.

TERM

Set Terminating Character Type.

Input:

TERM 0

TERM 1

TERM 2

, or

TERM 3

Returned:

Nothing

Remarks:

Sets the terminating character type from 0 to 3 defined as follows:

= Carriage return and line feed (CR)(LF

EOI

)

= Line feed and carriage return (LF)(CR

EOI

)

= Line feed (LF

EOI

)

= No terminating characters – EOI line set with last data byte if enabled (End)

Terminating characters are sent when the Model 330 completes its message transfer on

output. They also identify the end of an input message. This command works only with the

IEEE-488 Interface and does not change the serial terminators.

Содержание 330









































































































Результаты поиска

Содержание 330

Отзывы:

Lakeshore 330, Руководство пользователя, Страница: 55 / 104

Результаты поиска

Содержание 330

Отзывы: